|
![]() |
|
・ ・ |
|
|
➣ Live image page setup panel>Clicking the [Image quality] tab enables you to set the image quality. |
(1) Select [Light control mode] - For outdoor installation: Set [Outdoor scene] or [ELC]. - For indoor installation: Set [Indoor scene(50Hz)] or [Indoor scene(60Hz)]. 50 Hz/60 Hz can be used differently depending on the region. |
|
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Image] or [Image/Audio] in the Advanced menu on the left>[Image adjust] in the [Image quality] tab>Click [Setup] to display the image quality adjustment setting screen. |
(1) Select [White balance] ・ Select from [ATW1], [ATW2], and [AWC]. |
[ATW1] |
|
[ATW2] |
|
[AWC] |
|
|
|
➣ Live image page setup panel>Clicking the [Image quality] tab enables you to set the image quality. |
(1) Select [D&N] ・ Select from [Off], [Auto1(Normal)], and [Auto2(IR Light)]. |
[Off] |
|
[Auto1(Normal)] |
|
[Auto2(IR Light)] |
|
[Auto3(SCC)] |
|
(1) Remove the enclosure (2) Insert a microSD memory card into the slot |
|
|
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Display]>Advanced Menu>[Basic]>When [SD memory card] is clicked, the SD Memory Card setup page is displayed. |
(1) Select [Recording format] streams (2) Select [Save trigger] and click [Set]. (3) Click [Live] in the upper left corner and click the camera control panel button. ・ The camera control panel is displayed. (4) Click [Start] on [Rec. on SD] ・ Start recording to the SD Memory Card manually. ・ You can stop recording by clicking [Stop]. After stopping, you can resume recording by clicking [Start]. |
|
|
➣ Camera control panel of the live image page>Clicking [Playback of recording (Log disp.)] displays the log list. |
(1) Display the live image page and click the camera control panel button. (2) Click the [Log/Play] [Start] button ・ The Log List screen is displayed in a separate window. (3) Click the shooting date and time displayed below [Time] ・ The playback page is displayed and the saved image is played. |
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Set]>Advanced Menu>[Easy Setup]>Clicking on the [Event action] tab displays the configuration page. |
|
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Display]>Advanced Menu>Clicking [Alarm] displays the configuration page. |
|
|
![]() |
(1) (PTZ only)Select the preset position number to be set for the motion detection area and click [Start]. ・ The Set Operation Detection Area screen is displayed. |
(2) Drag in the image to set the area. ・ You can set the areas in order. (3) Adjust the [Detection area] and [Detection sensitivity] using the slider bar and then click [Set]. |
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Ext. software] in the Advanced menu on the left>Clicking [Setup >>] in [AI-VMD (Camera 1)], [AI-VMD (Camera 2)], [AI-VMD (Camera 3)], and [AI-VMD (Camera 4)] displays the setting window. |
(1) Click [Ext. software] in the Advanced menus (2) Select the camera you want to set from [AI-VMD (camera 1)], [AI-VMD (camera 2)], [AI-VMD (camera 3)], and [AI-VMD (camera 4)], and click [Setup >>]. ・ The AI-VMD setting screen is displayed. (3) Select [Detection mode] in [1.Area setting] and set up detection areas. (4) Click [2.Detailed setting] to set the detection sensitivity, detection time, and size of the person to be detected. |
|
|
(1) Select the desired part by dragging or clicking on the multi part screen of the live image page. ・ The PTZ part aligns the angle of view with the selected part and is displayed on the screen. |
|
|
・ Refer to the following support video for the HTTPS setting method (Pre-installed). |
・ For information about how to configure HTTPS (CA certificate), refer to the following support video. |
|
|
➣ Live image page setup panel>[Stream] tab>Set in [Image capture mode] of [Common]. |
|
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Basic] in the Advanced menu on the left>Configure in the [Overlay image] tab. |
(1) Select an image with [Overlay] set to [On]. (2) Set [Position], [Permeation], and [Selection of color to be penetrated] (3) Click [Set] |
|
➣ Live image page setup panel>Use the [Stream] tab. The streams of H.265 and H.264 images are set in [Stream] on the [Stream] tab. |
・ ・ ・ Refer to the User manual for details of each setting method. |
|
・ Fixed bit rate: H.265 (or H.264) images are delivered at the bit rate set by [Max bit rate (per client) *]. ・ Variable bit rate: H.265 (or H.264) images are delivered at the frame rate set by [Frame rate*] while maintaining the image quality level set by [Image quality]. At this time, the bit rate is varied within the maximum bit rate set by [Max bit rate (per client) *]. The recording capacity varies depending on the [Image quality] settings and object conditions. ・ Specify Frame Rate: H.265 (or H.264) images are delivered at the frame rate set by [Frame rate*]. ・ Best effort delivery: Depending on the bandwidth of the network, H.265 (or H.264) images are delivered with varying bit rates within the maximum bit rate set by [Max bit rate (per client) *]. |
|
➣ Live image page setup panel>[Detailed setting]>[Camera detailed setting]>[Image] or [Image/Audio] in the Advanced menu on the left>Clicking [Image] displays the Smart Coding configuration. |
![]() This image is for reference. It is different from the actual view of the screen. |
[Smart VIQS] |
|
[Smart P-picture control] |
|
[GOP control] |
|
|
|