3Setting

This chapter explains the items that can be set from the camera's live image.
You can set general items for each function in live pictures.
For items that cannot be set from live pictures, set them from the Advanced menu.
For how to display live pictures, refer to the following.
→2.3　Viewing images from a PC
For details on how to set each item from the Advanced menu, refer to the following.
→5.3　Camera Advanced Menu Screen

・Refer to the catalog specifications for the functions installed in each model.

3.1Displaying the configuration panel from the PC

The main settings of the camera are made on the Setup panel.

[Important]

・Configuration panels can only be operated by users with [1. Administrator] access levels. For details on how to set the access level, refer to the following.
→13.1　[User auth.] to configure user-authentication

3.1.1How to display

1

Displays Live image pages.
→2.3.1　View camera images

2

In the Live image pages

Click the button to display the setting panel.
Press again to hide it. For more information on this panel, please refer to the following.
→3.1.3　Setting Panel Screen

3.1.2How to operate

1

Click on each tab in the Settings panel.

2

Enter each item on the setting page.

[Note:]

・Some items cannot be set depending on the main area display.

If the desired item is not displayed,

Click or press the scroll bar to display the items you want to set.

3

Once the entry is complete, click to confirm the entry if [Set] is available. Otherwise, it is confirmed when the set value is selected.

[Important]

・If there are several buttons in the [Set], [Register], and [Execute] pages, click the [Set], [Register], and [Execute] buttons for each item.

3.1.3Setting Panel Screen

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

Compact dome camera, New X Fixed Cameras

PTZ camera

Multi-directional camera

①

[Basic] tabs
[Basic] displays the tabs. On the [Basic] tab, you can set the camera titles and display characters.
→3.2　[Basic] to perform basic settings

②

[Stream] tabs
[Stream] displays the tabs. On the [Stream] tabs, you can set up imaging modes, JPEGs, streams, etc.
→3.3　[Stream] for setting images

③

[Image quality] tabs
[Image quality] displays the tabs. In the [Image quality] tabs, you can set the image quality.
→3.4　[Image quality] for setting image quality

④

[Zoom]Tab
[Zoom] displays the tabs. On the [Zoom] tab, you can set zooming and other settings.
→3.5　[Zoom] for setting EX zoom
→3.6　[Zoom] for set zoom/focus

⑤

[Audio] tabs
[Audio] displays the tabs. The [Audio] tabs configure audio-related settings.
→3.7　[Audio] for setting sound

⑥

[Alarm] tabs
[Alarm] displays the tabs. The [Alarm] tabs configure the alarm settings.
→3.8　[Alarm] to set alarm

⑦

[Detailed setting] tabs
[Detailed setting] displays the tabs. On the [Detailed setting] tabs, you can migrate to advanced settings and set up control panels.
→3.9　[Detailed setting] for switching to advanced settings and setting related to the displayed images

3.2[Basic] to perform basic settings

The [Basic] tabs set the camera titles and display settings. See the [Basic] tabs on the Advanced Basic Page for a detailed explanation of the settings and notes for settings.
→8　[Basic] for basic setup of the machine

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Basic]

Set basic items such as camera title.

・

[Camera title]
Enter the this product name. The entered name is displayed in the camera title.

[Note:]

・[MULTI] [Image rotation] by cameras [date and time]&Set in [Characters on Screen].

Date and time&Characters on screen

Specify the display position and size of the character string to be displayed on the screen.

・

[Camera]
Select from [Camera 1] to [Camera 4] to individually set the following items for the selected camera.

・[Image rotation]

・[Camera title on screen display]

・[Camera title on screen(Line 1)]

・[Camera title on screen(Line 2)]

・[Camera title position]

・Date and time&In-screen text display format

・[Character size]

[Note:]

・[MULTI] Only the Multi-directional camera can be selected for [Camera].

・[MULTI] [Image rotation] can be selected for 2-eye Multi-directional cameras only.

・ [Image rotation]
Select from [0 °(Off)], [90°] and [180 °(Upside-down)], and [270°].

・ [Camera title on screen display]
Use [On]/[Off] to set whether the strings are displayed on the images.
When set to [On], the character strings entered in [Camera title on screen] are displayed at the position selected in [Position].

・ [Camera title on screen(Line 1)] /[Camera title on screen(Line 2)]
Enter a character string to be displayed in the image.

・ [Camera title position]
Select the position where the character string is displayed in the image.

・ [Time/date and camera title on screen - display format]
Sets the display format to either [Permeation] or [Opaque].

・ [Character size]
Select the date and time displayed in the image and the character size of the character string.

[Installation position]

・

[Tilt adjustment lever position]
Select the [Tilt adjustment lever position] set when the cameras are installed.

3.3[Stream] for setting images

The [Stream] tabs configure settings for JPEG, H.265, and H.264 images.
For a detailed explanation of the settings and notes for setting, refer to the [Image] tabs on the image/audio pages in the detailed settings.
→9.1　[Image] to set the imaging modes

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Common]

Set the common items for JPEG and stream.

・

[Image capture mode]
Select the image to be displayed on the live image, etc.

・

[Initial display stream]
Select the image to be displayed on the live image page.

[Stream]

Select the number of the stream and set the [Stream transmission].

・

[Stream transmission]
On/Off sets whether to deliver H.265 (or H.264) images.

・

[Stream encoding format]
Select the compression method for the stream to be delivered.

・

[Image capture size]
Select the resolution of the H.265 (or H.264) image.

・

[Image quality]
Select the quality of the H.265 (or H.264) image.

・

[Transmission priority]
Set the stream delivery mode.

・

[Frame rate*]
Sets the frame rate.

・

[Max bit rate (per client) *]
Select the H.265 (or H.264) bit rate for one client.

・

[Auto VIQS]
Images are distributed so that the quality of images in moving places is high and the amount of data in other places is low.

・

[Smart VIQS]
Images are distributed so that the amount of data decreases while maintaining high image quality in areas with objects (head, people, cars and motorcycles) and low/medium/medium image quality in other areas.

・

[Smart P-picture control]
To reduce the amount of data, control the generation of data (macroblock) as little as possible except where there is an object (head, person, car, or motorcycle).

・

[GOP control]
The GOP control reduces the amount of data.

[JPEG]

Configure the JPEG [Image capture size] [Image quality] [Transmission interval].

・

[Image capture size]
When displaying JPEG images, select the resolution of the images to be displayed.

・

[Image quality]
Set the quality of JPEG images at each resolution.

・

[Refresh interval(JPEG)]
Select the rate at which the JPEG image is updated from the following.

3.4[Image quality] for setting image quality

On the [Image quality] tabs, you set image quality.
For a detailed explanation of the settings and notes for setting, refer to the [Image quality] tabs on the image/audio pages in the detailed settings.
→9.4　[Image quality] to set the image quality

[Image quality]

You can set various image quality adjustments such as brightness and sharpness level.

[Note:]

・[MULTI] Only Multi-directional cameras can be selected for [Camera selection].

・[MULTI] This item is not displayed when [Image capture mode] is in Quad/Dual mode.

・[MULTI] For [Common(Cam. 1-2)], [Super Dynamic], [Light control mode], [White balance], and [Intelligent Auto] can be set only for items that have not been developed in detail. To perform other advanced settings, select each camera.

・

[Camera selection]
Select the camera to set the image quality.

・[Common(Cam. 1-2)]: Sets the same settings for the cameras.

・[Camera 1]: Sets camera 1 image quality.

・[Camera 2]: Sets camera 2 image quality.

・[Camera 3]: Sets the image quality of camera 3.

・[Camera 4]: Sets camera 4 image quality.

・

[Brightness]
Adjust the brightness.
Move the slider bar in the [+] direction to brighten the image.
Move the slider bar in the [-] direction to darken the image.
Press [Reset] to return to the default brightness.

・

[Sharpness level]
Adjust the sharpness level (contour correction).
Moving the slider bar in the direction of [+] results in a sharp contour, and moving the slider bar in the direction of [-] results in a soft contour.
Press [Reset] to return to the default settings.

・

[Maximum gain]
Adjust the maximum gain. When the subject's illumination becomes dark, the gain automatically increases and the screen brightens.
Increasing the gain may increase the noise.
Move the slider bar in the [+] direction to increase the maximum gain.
Move the slider bar in the [-] direction to reduce the maximum gain.
Press [Reset] to return to the default settings.

・

[Digital noise reduction]
The digital noise reduction function automatically reduces noise at low illumination levels.
Move the slider bar in the direction of [+] to increase the effect of noise reduction. There may be a lot of afterimages.
Moving the slider bar in the direction of [-] reduces the noise reduction effect. There are fewer aftereffects.
Press [Reset] to return to the default settings.

・

[Super Dynamic]
On/Off is used to specify whether or not the super dynamic function can be activated.

・

[Light control mode]
Select the mode to control the light intensity.

・

[Maximum shutter]
The maximum exposure time adjusts the maximum storage time of the sensor.

・

[D&N]
Select the mode for switching between black and white images and color images.

・

[Intelligent Auto]
Set ON/OFF whether the intelligent auto function is enabled or not.

3.5[Zoom] for setting EX zoom

On the [Zoom] tab, you set the angle of view of the image displayed during zooming.
For a detailed explanation of the settings and notes for setting, refer to the [Image quality] tabs on the image/audio pages in the detailed settings.
→9.4.3　Adjust the angle of view with the EX zoom

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Zoom]

Set the field of field of field.

・

[Camera selection]
Select the camera to set EX zoom.

[Note:]

・[MULTI] Only Multi-directional cameras can be selected for [Camera selection].

・

[Extra zoom]
X1: Zoom (magnification) is 1.0 times.

Adjust the zoom factor to 1.0 times in the [Wide Angle] direction.

: Adjust the zoom factor in the [Telescope] direction.

3.6[Zoom] for set zoom/focus

Use Zoom and EX optical zoom to adjust the angle of view of the displayed image.
Adjust the focus by moving the lens focus to the optimal position. It can be adjusted manually or automatically.
→1.1.21.4　Adjust the zoom/focus

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Zoom]

Set the field of field of field.

・

[Camera selection]
Select the camera to set zoom and focus.

・

[Zoom ratio designation]
Adjust the zoom and focus simultaneously.
Press the slider bar to zoom in or out the angle adjustment frame in the image.
When you adjust the zoom (magnification) in the "telephoto" direction, only the image adjustment frame is reduced and you can specify the zoom (magnification) while checking the angle of view after the zoom is executed.
When the zoom (magnification) is adjusted in the "Wide angle" direction, the image itself is reduced or the frame for the zoom angle adjustment is enlarged. You can specify the zoom (magnification) while checking the image size after the zoom is executed.
Adjust the angle of view adjustment frame, and click [Execute] to zoom. Then, automatically adjust the focus to the object in the center of the window using the auto focus function.

・

[Manual zoom adjustment]
Adjust the zoom manually.

Adjust the zoom factor to 1.0 times in the [Wide Angle] direction.
X1: Zoom (magnification) is 1.0 times.

: Adjust the zoom factor in the [Telescope] direction.

・

[Manual focus adjustment]
Adjust the focus manually.
[Reset] returns focus (focus) to its default settings.
[Near]: Adjust the focus to the [Near].
[Far]: Adjust the focus to the [Far].

・

[Auto focus]
When [Execute] is clicked, the auto focus function is activated to automatically adjust the focus to the object in the center of the window.

・

[Focusing at Day & Night switching]
Select the focus adjustment method when switching between color image and black-and-white image from the following. For details, refer to our technical information website <Control No. C0315>.

3.7[Audio] for setting sound

The [Audio] tabs configure audio-related settings.
For a detailed explanation of the settings and notes for setting, refer to the [Audio] tabs on the image/audio pages in the detailed settings.
→9.5　[Audio] for setting sound

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Audio]

Sets sound and volume items.

・

[Mic input volume]
Set the volume of sound input to the computer. This setting is reflected in the volume of sound (listening) on the computer and the volume at [Audio recording].

・

[Audio transmission mode]
Set the communication mode for sending/receiving voice data between the computer and the PC.

・

[Audio input encoding format]
Select the compression method for the earpiece sound.

・

[Audio volume control mode]
Select how to use the volume cursor of the earpiece button on the live picture page.

3.8[Alarm] to set alarm

The [Alarm] tabs configure the alarm settings.
See the [Alarm] tabs on the alarm pages for detailed explanations of setting values and notes for setting values.
→12　[Alarm] to set the alarm

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

[Alarm]

Set terminal operation and alarm items.

・

[Terminal 1]
Set the operation of terminal 1.

・

[Terminal 2]
Set the operation of terminal 2.

・

[Terminal 3]
Set the operation of terminal 3.

・

[VMD alarm]
ON/OFF is used to specify whether or not to perform operation detection.
When set to [On], the entire area is specified in the operation detection area. To specify an arbitrary action detection area, set it on the [VMD area] tab of the alarm page of the advanced setting.
→12.5　[VMD area] for setting motion detection
The [VMD area] tabs on the advanced alarm pages are accessible from live picture links.

・

[Scene change detection (SCD) alarm]
ON/OFF is used to specify whether or not to perform undesired detection.
When set to [On], the entire area is specified in the disturbance detection area. To specify an optional disturbance detection area, use the [SCD area] tabs on the alarm pages in Advanced Settings.
→12.7　[SCD area] to set up undesired detection
The [SCD area] tabs on the advanced alarm pages are accessible from live picture links.

・

[Audio detection alarm]
ON/OFF is used to specify whether or not to perform sound detection.
When set to [On], all AI sounds are enabled. To configure the details of sound detection, use the [Audio detection] tabs on the alarm pages in Advanced Settings.
→12.9　[Audio detection] for setting sound detection
The [Audio detection] tabs on the advanced alarm pages are accessible from live picture links.

・

[Alarm deactivation time]
Sets the time when the alarm is detected and the detection operation is not executed. For example, if you set up an e-mail notification to a mobile terminal or a tablet terminal using an alarm, this setting prevents you from sending too much e-mail.

3.9[Detailed setting] for switching to advanced settings and setting related to the displayed images

[Note:]

・Refer to the catalog specifications for the functions installed in each model.

Function extension software

・

[Ext. software] buttons
Displays the menu for managing the function extension software and setting the schedule.
→6　[Ext. software] for managing and scheduling advanced software

Network

・

[Network] buttons
The Network Settings menu is displayed.
→14　Networking configuration [Network]

Maintenance

・

[Maintenance] buttons
This displays menus for checking the system log, software version upgrade, status check, and initialization of the computer settings.
→16　[Maintenance] to maintain the machine

Camera details

・

[Advanced settings page] buttons
The Advanced menu is displayed.
→5.3　Camera Advanced Menu Screen

Screen setting

・

[Color]
Select the background color of the operation panels and advanced menus from the [Light] [Dark].
→2.3.2　About live image pages

・

[Operation panel layout]
Select the position of the control panel from [Right], [Left], and [Lower].
→2.3.2　About live image pages