6.Other

INITIAL SETPress the button to initialize the main unit.INITIAL SETSee below for the position of the buttons.
Button
1.
Turn off the computer.
2.
Turn on the computer while pressing the [INITIAL SET] button.
3.
Press the [INITIAL SET] button for 15 seconds or longer after the power is turned on.
4.
Release the INITIAL SET button
Approximately two minutes later, the computer is started and the settings containing the network settings are initialized. If it does not start normally, try again.
The functions of this machine are implemented in software. We recommend that you first check the current software version if there is a problem with the operation of the computer.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting]>[Maintenance] of the Advanced menus on the left>Clicking on the [Upgrade] tabs displays the versioning window.
1.
Check software versions with [Firmware version]
The current software version can be checked.
Up-to-date versions of software may contain modifications to specific problems.
It is recommended to set the settings for image quality in the following order: Adjustment of visibility → Adjustment of color → Removal of noise.
1.
Adjust the visibility
[Light control mode], [Intelligent Auto], [Super Dynamic], [Contrast level], [High light compensation(HLC)], [Adaptive black stretch], [Adaptive highlight stretch], [Maximum gain], [Maximum shutter], pedestal level
2.
Adjust the color
[White balance], [Chroma gain level]
3.
Remove the noise
[Digital noise reduction], [Sharpness level]
Refer to the User Manual for details of each function.

・The image quality adjustment function may affect each other.


・If necessary, adjust the brightness level of the screen.


Adjust the object brightness.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Brightness] of [Image quality]
Moving in the [+] direction brightens the image.
Move in the [-] direction to darken the image.
[-]
Produce darker images
[+]
Create the brighter the photos





In dark scenes, the image becomes brighter by increasing the maximum gain.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Maximum gain] to [+]
Maximum gain: 6
Maximum gain: 11



Increasing the maximum gain increases noise.
Increasing the maximum shutter makes the images brighter.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Select [Maximum shutter]
Selecting [Maximum shutter] longer than [Max. 1/30s] brightens the image because the amount of light entered increases.
Increasing the maximum shutter increases the blur.
Maximum shutter : 1/30
Maximum shutter : 4/30



When Super Dynamic is set to ON, both bright and dark areas are reproduced faithfully, even when shooting in a place with a large brightness difference.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Set [Super Dynamic] to [On]
Set [Super Dynamic] to [Off] when the following phenomena are observed depending on the lighting condition.

–If flicker or color change occurs


–Noise in the bright area on the screen


Super Dynamic: Off
Super Dynamic: On
Level: 28



By setting [Backlight Corrector], the darkness of the indoor object is suppressed (brighter indoor object).
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Set to [Back light compensation(BLC)] in the [Super Dynamic] [BLC/ HLC]
If [Super Dynamic] is set to [On] or [Intelligent Auto] is set to [On], [Backlight Compensation] cannot be set.
Back Light Correction: Off
Back light correction: On
Level: 16



By setting [High light compensation(HLC)], bright lights such as car headlights suppress the brightness of the object.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Select [High light compensation(HLC)] in [Super Dynamic] [BLC/ HLC]
If [Super Dynamic] is set to [On] or [Intelligent Auto] is set to [On], it cannot be set to [High light compensation(HLC)].
High light compensation : Off
High light compensation : On



Adjust the [Adaptive black stretch] to brighten the dark areas of the images.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Adjust [Detail setting] [Adaptive black stretch] levels to [+]
Level: 128
Level: 255



Adjust the pedestal level to adjust the black level of the image.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Adjust the pedestal level of the [Detail setting].
Moving in the [+] direction brightens the image.
Move in the [-] direction to darken the image.
[+] direction
Create the brighter the photos
[-] direction
Produce darker images


By adjusting the [Contrast level] to increase the contrast between the light and dark images, visibility of the object with less contrast can be improved.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Adjust [Detail setting] [Contrast level] levels to [+]
Level: 128
[+] direction
Increase the contrast



Flickers are automatically corrected by using [Light control mode].
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Select [Flickless (50 Hz)] or [Flickless (60 Hz)] for [Light control mode].
Use 50 Hz/60 Hz depending on the region.
Using [Intelligent Auto], the camera identifies object with scenes (backlights, outdoors, night scenes, etc.) and facial movements of people. The camera automatically adjusts the amount, gain, shutter speed, and contrast of light entering the camera from the camera's lenses to make it easier to see a moving object.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Adjust [Face priority level (Brightness)] and [Motion priority level (Shutter)] with [Intelligent Auto] set to [On].
By adjusting in the [+] direction, blurring of the object will be reduced.
Increasing the level in a low illumination environment increases noise.
Off (person blurred)
On (less blurring)



Shortening the maximum shutter reduces blur.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Selecting a shorter [Maximum shutter] than [Max. 1/30s]
If [Maximum shutter] is set to a shorter time than [Max. 1/30s], blur is reduced.
In low illumination environments, shortening the maximum shutter will darken the object and increase the noise.
Maximum shutter : 1/30
Maximum shutter : 1/250



Reducing the effects of noise reduction by adjusting the [Digital noise reduction] reduces the blur.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Digital noise reduction] in the [-] direction.
If the effect of noise reduction is reduced, the noise will increase.
Level: 128
Level: 100
Reduce the blur



Adjust the [Sharpness level] to sharpen the outline of the images.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Sharpness level] to [+]
Level: 10
Level: 31
Sharpen the contour



Adjust the [Chroma gain level] to adjust the darkness.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Adjust the [Chroma gain level] of [Basic adjustment]
Moving in the [+] direction produces a bright and bright color.
Move in the [-] direction to make a calm color.
[-]


[+]



If the color is affected by a sodium lamp, use [White balance] to adjust the color.
Live image pages configuration panels>[Detail setting]>[Camera detailed setting] [Advanced settings page]>[Image] or [Image/Audio] of the Advanced menus on the left>[Image adjust] in the [Image quality] tabs>When [Advanced settings] is clicked, the image quality adjustment setting window is displayed.
1.
Select [ATW2] in [White balance]
The camera automatically adjusts the white balance under a sodium lamp.
Effect of sodium lamp
No effect of sodium lamp



Adjusting the [Sharpness level] to make the images soft reduces the noise around the object.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Sharpness level] in the [-] direction.
Level: 31
Level: 5
Have soft contours



By adjusting the [Digital noise reduction] and increasing the effects of noise reduction, noise is reduced.
Live image pages configuration panels>Clicking the [Image quality] tabs enables you to set the image quality.
1.
Adjust the [Digital noise reduction] to [+]
Increasing the effects of noise reduction increases blur.
Level: 90
Level: 255
Reduce noise



Check the symptoms on this table before asking for repair.
Contact the dealer from whom you purchased the watch if you do not recover from any of these problems or if you have symptoms other than those listed in this table.
Phenomenon
Cause
Countermeasures
Reference
Be not powered on
For a PoE power supply
Installation

・Is the network cable connected to the power supply device for PoE (IEEE 802.3af)?


・Check if it is connected.


・Some power supply devices that can connect multiple PoE terminal devices will not supply power if the total power supply exceeds the limit.


・Refer to the operation manual of the PoE power supply system.


The LINK lamp does not illuminate orange when the network cable is connected.

・Is the Ethernet cable connected correctly to the machine?


・Connect the Ethernet cable properly.



・Is the hub or router to which the machine is connected working correctly?


・Check that your hub or router is working correctly.


・Is the Ethernet cable connected to the machine broken?


・Replace with another Ethernet cable.


The SD ERROR lamp illuminates red.

・An SD Memory Card read/write error has occurred. Is an abnormal memory card inserted?


Replace the SD Memory Card with a normal one.

Removing the enclosure and checking the screen may reveal shadows in four corners.
Depending on the position of the light shielding rubber on the lens, it may appear on the shooting screen.
If the enclosure is attached to the camera, the light shielding rubber returns to the normal position. This is not a problem with the camera.

White spots or bars may appear on the screen when shooting black and white using IR LED Light.
When adjusting the image angle of the camera, the IR LED Light may be reflected back to the camera enclosure at about 70°-85° TILT and 50°-100° YAW and may be reflected in the video.
Adjust TILT to less than 70 degrees or YAW to less than 50 degrees to avoid the effects of reflections.

Do not touch lenses or Dome covers directly.
If dirty, image quality may deteriorate.
Impact on image/image quality
Image quality may deteriorate or the image may be difficult to see under the installation conditions below.
-
When raindrops adhere to the Dome covers during rainfall
-
When snow adheres to the Dome covers due to wind during snow accumulation (the degree of snow adherence depends on the amount of snow fall and the snow quality)
-
Contamination of the Dome covers due to airborne dust or automotive exhaust
About the built-in microphone
-
If water adheres to the opening of the built-in microphone, the sound volume may drop. Allow it to dry thoroughly before use.
-
When cleaning the opening of the built-in microphone, do not stick it with a sharp object. Failure to heed this warning may result in failure.
Do not apply strong shocks to the Dome covers.
Otherwise damage or flooding can result.
Batteries
The battery is built into the unit. Do not leave the battery in an environment exposed to excessive heat from sunlight or fire.
If the machine is no longer in use, do not leave it unattended and must be removed.
Open Source Software
-
This product includes open source software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL), and others.
-
You may obtain the source code of such software and reproduce, distribute and modify it in accordance with GPL or LGPL.
-
For more information on licensing open source software and source code, refer to the [Support] page [For information on OSS used in this system] on the computer's configuration menu to view the information displayed.
-
Please note that you cannot answer questions about the source code.
Copyright
Except for open source software licensed under GPL/LGPL or otherwise, transfers, copying, disassembly, decompilation, and reverse engineering of the software contained in this product are prohibited. In addition, any act of export that violates the export laws and regulations of all software included in this product is prohibited.
For trademarks and registered trademarks
-
Microsoft, Windows, Windows Media, Internet Explorer, Microsoft Edge, and ActiveX are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries.
-
Intel, Intel Core is a trademark of Intel Corporation or its subsidiaries in the United States and/or other countries.
-
Adobe, Acrobat Reader and Adobe Reader are trademarks of Adobe.
-
The microSDXC Logo is a trademark of SD-3C, LLC.
-
iPad and iPhone are trademarks of Apple Inc. registered in the United States and other countries.
-
Android and Google Chrome are trademarks of Google LLC.
-
Firefox is a trademark of the Mozilla Foundation in the United States and other countries.
-
Other company names and product names described in this manual are trademarks or registered trademarks of each company.
 
IN NO EVENT SHALL i-PRO Co.、 Ltd. BE LIABLE TO ANY PARTY OR ANY PERSON, EXCEPTFOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE CASES,INCLUDING BUT NOT LIMITED TO BELOW:
1.
ANY LOSS OR DAMAGE, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT,SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THEPRODUCT;
2.
ANY INCONVENIENCE, LOSS, OR DAMAGE CAUSED BY INAPPROPRIATE USE ORNEGLIGENT OPERATION OF THE USER;
3.
ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR ORMODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THEMALFUNCTION OR TROUBLE;
4.
INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TOANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
5.
ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISINGOUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
6.
ANY CLAIM OR ACTION FOR DAMAGES BROUGHT BY ANY PERSON OR ORGANIZATIONAS A PHOTOGRAPHED SUBJECT DUE TO VIOLATION OF PRIVACY CONCERNING ASURVEILLANCE CAMERA'S PICTURE OR SAVED DATA, FOR SOME REASON (INCLUDINGUSE WHEN USER AUTHENTICATION ON THE AUTHENTICATION SETTING SCREEN IS SETTO OFF)、 BECOMING PUBLIC OR BEING USED FOR ANY PURPOSE;
7.
LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE (INCLUDING INITIALIZATION OFTHE PRODUCT DUE TO FORGOTTEN AUTHENTICATION INFORMATION SUCH AS A USERNAME AND PASSWORD)。
Limitation of liability
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OFTHE THIRD PARTY'S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICALERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THEIMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S)。
Since this equipment is connected to the network, it may be damaged as follows.
Leakage or leakage of information via the machine
Malicious operation of the Aircraft by a malicious third party
Interference or stoppage of the Aircraft by a malicious third party
In order to prevent such damage, take adequate network security measures including the following measures under the responsibility of the customer.
Use the machine on a secure network using firewalls, etc.
Confirm that computer viruses and malicious programs are regularly checked and exterminated when the computer is connected to the system.
Use user authentication, set user names and passwords, and restrict users who can log in to protect against unauthorized attacks.
To prevent image data, authentication information (user name, password), alarm mail information, FTP server information, DDNS server information, etc., from being leaked on the network, measures such as restricting access by user authentication are implemented.
All browsers must be closed after administrator access to the machine.
The password of the administrator is changed periodically. In addition, authentication information (user name, password) shall be appropriately stored so that it is not visible to third parties.
Do not install the equipment or cables in a place where they are easily destroyed.