Dome-Kameras

WV-SFN310 i-PRO

Indoor Dome Network camera

DISCONTINUED PRODUCT

Super Dynamic HD Dome Network Camera

Successor model : WV-SFN310A

  • Onvif Profile S

• 720p HD images up to 60 fps*1
• Super high resolution at HD/1,280 x 720 created by high sensitivity MOS Sensor.
• Enhanced Super Dynamic*1 and ABS (Adaptive Black Stretch) technologies deliver 133 dB wider dynamic range compared to conventional cameras.
• Multi process NR & 3D-DNR ensures noise reduction in various conditions.
• High sensitivity with Day & Night(Electrical) function: 0.01 lx (Color), 0.008 lx (B/W) at F1.6
• New camera attachment bracket allows an easy camera installation toward all four directions.
• Face Super Dynamic technology ensures clear face image.
• Newly developed dome cover provides clearer images above the horizontal. Thereby, it expands the tilting range of the lens.
• Face detection function detects the position of human face and the information is sent by XML or video stream. (Optional)
• Can be added new intelligent extension software (Optional) in addition to built-in VMD (Video Motion Detection), alarm function.
• Fog compensation function equipped as standard.
• Super Chroma Compensation function realizes a better color reproducibility even in low illumination.
• Supports SSL, DDNS (viewnetcam, RFC2136)
*1 Super Dynamic function is automatically set off on 60fps mode

Camera

COMPONENT SPECIFICATION
Image Sensor Approx. 1/3 type MOS image sensor
Effective Pixels Approx. 1.3 mega pixels
Scanning Mode Progressive scan
Scanning Area 4.864 mm (H) x 3.891 mm (V) {3/16 inches(H) x 5/32 inches(V) }
Minimum Illumination Color: less than 0.01 lx, BW: 0.008 lx (F1.6, Maximum shutter :Max. : Off (1/30s), Gain : On(High))
Color: less than 0.0007 lx, BW 0.0005 lx (F1.6, Maximum shutter : Max. 16/30s, Gain:On(High))
White Balance AWC (2,000 ~ 10,000 K), ATW1 (2,700 ~ 6,000 K), ATW2 (2,000 ~ 6,000 K)
Light Control Mode Outdoor scene : Automatic integration of ALC and ELC
Indoor scene [50 Hz] : Automatic integration of ALC and ELC with flickerless
Indoor scene [60 Hz] : Automatic integration of ALC and ELC with flickerless
Shutter Speed 1.3 mega pixel [16:9](60 fps mode)]
OFF(1/60), 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,1/10000 Other than
1.3 mega pixel [16:9](60 fps mode)]
OFF(1/30), 3/100, 3/120, 2/100, 2/120, 1/100, 1/120, 1/250,1/500, 1/1000,1/2000, 1/4000, 1/10000
Super Dynamic On(High) / On(Normal) / Off
Face Super Dynamic ON / OFF (Only at Super Dynamic : ON)
Adaptive Black Stretch ON / OFF (Only when Super Dynamic OFF )
Fog Compensation ON / OFF (Only when Super Dynamic / Adaptive black stretch: Off)
AGC ON (LOW, MID, HIGH) / OFF
Electronic Sensitivity Up max. 1/1000 s, max. 1/500 s, max. 1/250 s, max. 1/100 s, max. 1/60 s, max. 1/30 s, max. 2/30 s, max. 4/30 s, max. 6/30 s, max. 10/30 s, max. 16/30 s
Day/Night Electrical Mode: OFF / AUTO
Dynamic Range 133 dB typ. (Super Dynamic: ON, Light Control Mode : indoor)
Digital Noise Reduction High / Low
Video Motion Detection 4 areas, Sensitivity : 15 steps, Detection size : 10 steps
Privacy Zone Up to 8 zones
VIQS Up to 8 zones
Camera Title (OSD) Up to 20 characters (alphanumeric characters, marks)
Electric Zoom TELE / WIDE , Auto Coarse adjustment of Focus
Focus Adjustment Focus Assist
Lens Distortion Compensation 256 steps

Lens

COMPONENT SPECIFICATION
Vari Focal Length 2.8 ~ 10mm {1/8 inches –13/32 inches}
Angular Field of View [16 : 9 mode] Horizontal : 27.9° (TELE) –100.5° (WIDE)
Vertical : 15.7° (TELE) –54.8° (WIDE)
[4 : 3 mode] Horizontal : 27.9° (TELE) –100.0° (WIDE)
Vertical : 21.0° (TELE) –73.9° (WIDE)
Maximum Aperture Ratio 1 : 1.6 (WIDE) ~ 1 : 4.0 (TELE)
Focusing Range 0.3 m ~ ∞

Adjusting Angle

COMPONENT SPECIFICATION
Adjusting Angle Horizontal: ± 180°, Vertical: ± 85°,Image tilt adjustment range: -225°(Left) to +120°(Right)

Browser GUI

COMPONENT SPECIFICATION
Cropping H.264(1) / H.264(2) / H.264(3) / H.264(4) / H.264(all) / JPEG(1) / JPEG(2) / JPEG(3) Up to 4 image capture areas can be specified
Camera Control Brightness, AUX ON / OFF
Display Mode Spot, Quad : Image from 16 cameras can be displayed in 4 different Quad screens or 16 split screen (JPEG only). 20 characters camera title available.
Digital Zoom 1x, 2x, 4x controlled by browser GUI
Camera Title Up to 20 alphanumeric characters
Clock Display Time : 12H/24H, Date : 5 formats on the browser, Summer time (Manual)
Alarm Control Reset
One Shot Capture A still picture will be displayed on a newly opened window.
Audio Mic (Line) Input : ON / OFF
Volume adjustment : Low / Middle / High
SD Memory Data Download Still or motion Images recorded in the SDXC/SDHC/SD memory card can be downloaded.
GUI/Setup Menu Language English, Italian, French, German, Spanish, Portuguese, Russian, Chinese, Japanese
System Log Up to 100 (Internal)
Up to 4,000 (SDXC/SDHC/SD memory when the recording format is set to JPEG.) error logs
Supported OS Microsoft® Windows® 8.1, Microsoft® Windows® 8, Microsoft® Windows® 7, Microsoft® Windows Vista®
Supported Browser Windows® Internet Explorer® 11.0 (32 bit), Windows® Internet Explorer® 10.0 (32 bit), Windows® Internet Explorer® 9.0 (32 bit),Windows® Internet Explorer® 8.0 (32 bit), Windows®Internet Explorer® 7.0 (32 bit)

Network

COMPONENT SPECIFICATION
Network IF 10Base-T / 100Base-TX, RJ-45 connector
Image Resolution Image Capture Mode: 1.3 mega pixel [16:9] (30/60fps)
1,280 x 720 / 640 x 360 / 320 x 180 / 160 x 90
Image Capture Mode: 1.3 mega pixel [4:3] (30fps)
1,280 x 960 / 800 x 600 / 640 x 480 / 400 x 300 / 320 x 240 / 160 x 120
H.264 [Transmission Mode]
Constant bitrate / Framerate priority / Best effort / Advanced VBR
[Frame Rate]
1 / 3 / 5 / 7.5 / 10 / 12 / 15 / 20 / 30 / 60 fps
[Bit Rate/Client]
64 / 128 / 256 / 384 / 512 / 768 / 1,024 / 1,536 / 2,048 / 3,072 / 4,096 / 6,144 / 8,192 / 10,240 / 12,288 / 14,336 / 16,384 / 20,480 / 24,576 kbps
[Image Quality]
LOW / NORMAL / FINE
[Refresh interval]
0.2 / 0.25 / 0.33 / 0.5 / 1 / 2 / 3 / 4 / 5s
[Transmission Type]
UNICAST / MULTICAST
JPEG [Image Quality]
10 steps
[Refresh interval]
0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying both JPEG and H.264 images.)
[Transmission Type]
PULL / PUSH
Audio Compression G.726 (ADPCM) 32 kbps / 16 kbps, G.711 64 kbps / AAC-LC
Audio Mode OFF / Mic (Line) input / Audio output / Interactive (Half duplex) / Interactive (Full duplex)
Authentication for Audio Level 1 only / Level 2 higher / All users
Total Bit Rate 64 / 128 / 256 / 384 / 512 / 768 / 1,024 / 2,048 / 4,096 / 8,192 kbps / Unlimited
Supported Protocol IPv6 : TCP/IP, UDP/IP, HTTP, HTTPS, FTP, SMTP, DNS, NTP, SNMP, DHCPv6, RTP, MLD, ICMP, ARP
IPv4 : TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP
FTP Client Alarm image transmission, FTP periodic transmission (When the FTP transmission is failed, backup on an optional SDXC/SDHC/SD memory card is available.)
No. of Simultaneous Users Up to 14 users (Depends on network conditions)
SDXC/SDHC/SD Memory Card (Option) # Manufactured by Panasonic (SD speed class 4 or higher)
# Use the SD memory card that complies with UHS-1 (Ultra High Speed-1) in the case of SD Speed Class 10.
H.264 recording : Manual REC / Alarm REC (Pre/Post) / Schedule REC/ Backup upon network failure Compatible (JPEG only)
JPEG recording : Manual REC / Alarm REC (Pre/Post) / Backup upon network failure Compatible SD (SDHC/SDXC) card: Panasonic 2 GB, 4 GB*, 8 GB*, 16 GB*, 32 GB*, 64GB** model
*SDHC card, ** SDXC card (except miniSD card and microSD card)
Cellular Phone Compatibility JPEG image, AUX control (by access level)
Mobile Terminal Compatibility iPad, iPhone, iPod touch (iOS 4.2.1 or later), Android™ Terminal

Alarm

COMPONENT SPECIFICATION
Alarm Source 3 terminals input, VMD, Command alarm, Audio detection alarm
Alarm Actions SDXC/SDHC/SD memory recording, E-mail notification, HTTP alarm notification Indication on browser, FTP image transfer, Panasonic protocol output
Alarm Log With SDXC/SDHC/SD memory card : Up to 50,000 logs for each SD memory card
Schedule Alarm / VMD / Access permission / H.264 recording / Scene file

Input/Output

COMPONENT SPECIFICATION
Monitor Output (for Adjustment) VBS : 1.0 V [p-p]/75 Ω, NTSC / PAL composite, ø3.5mm mini jack MONITOR OUT conversion plug included
Built-in Microphone Electret condenser microphone
External I/O Terminals ALARM IN 1, ALARM IN 2/ALARM OUT, ALARM IN 3/AUX OUT

General

COMPONENT SPECIFICATION
Safety UL (UL60950-1), C-UL (CAN/CSA C22.2 No.60950-1), CE, IEC60950-1
EMS FCC (Part15 ClassA), ICES003 ClassA, EN55022 ClassB, EN55024
Power Source and Power Consumption DC power supply: 12 V DC/310 mA/Approx. 3.7 W
PoE Device: 48 V DC/120 mA/Approx. 5.8 W* (Class 2 device)
* ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
Ambient Operating Temperature -10°C ~ +50°C (14 °F ~ 122 °F)
Ambient Operating Humidity 20 ~ 90 % (no condensation)
Dimensions ø129.5 mm x 101 mm (H) {ø5-3/32 inches x 3-31/32 inches (H)} Dome radius 40 mm {1-9/16 inches}
Mass (Approx.) 0.45 kg {1 lbs}
Finish Main body: ABS resin, sail white / Dome section: Clear acrylic resin

Specifications

Data Sheet

A&E Spec Sheet

Manuals

Installation Guide

User Manual/Operating Instruction

Firmware/Software

Firmware

WV-SFV311 etc. Firmware

WV-SFV311 etc. Firmware

NTSC/PAL
   How to upgrade firmware in 2 steps.
   (Click here for detail)

  • In case of firmware updating from 1.xx to 2.xx, you have to upgrade version 9.99 once, then upgrade 2.xx. Also for upgarding from 2.xx to 4.10 (or earlier), you have to upgrade version 4.00 once, then upgrade 4.10 (or later).

  • Please click here to request the firmware version 9.99 as providing the firmware is on request only; complete the form with the model number of your camera and "Request firmware version 9.99", then click "Submit" button.
    Please clear the cache memory or access with another internet browser if you cannot access the form.

  • Important information about backing up/restoring the settings data of camera firmware ver 1.71 or older (Click here for detail)
WV-SFV311 etc. Firmware (Chinese)

WV-SFV311 etc. Firmware (Chinese)

Chinese
   How to upgrade firmware in 2 steps.
   (Click here for detail)

  • In case of firmware updating from 1.xx to 2.xx, you have to upgrade version 9.99 once, then upgrade 2.xx. Also for upgarding from 2.xx to 4.10 (or earlier), you have to upgrade version 4.00 once, then upgrade 4.10 (or later).

  • Please click here to request the firmware version 9.99 as providing the firmware is on request only; complete the form with the model number of your camera and "Request firmware version 9.99", then click "Submit" button.
    Please clear the cache memory or access with another internet browser if you cannot access the form.

  • Important information about backing up/restoring the settings data of camera firmware ver 1.71 or older (Click here for detail)

Release Note

Image/CAD/BIM

Image Data

BIM Data

WV-SFN3,5,6 Series BIM

WV-SFN3,5,6 Series BIM

Building information models (BIMs) files

Other

Technical Document

How to firmware two-stage version up

How to firmware two-stage version up

How to upgrade firmware version 2.00 (or newer) in 2 steps and/or version 4.10 (or newer).

WV-SFV631L, SFV611L etc. How to Upgrade (Ver1.71 or older)

WV-SFV631L, SFV611L etc. How to Upgrade (Ver1.71 or older)

Important information about backing up/restoring the settings data of camera firmware ver 1.71 or older
WV-SW397, SFN311 etc. Addendum

WV-SW397, SFN311 etc. Addendum

Added to Compatible SDXC memory cards
WV-SW397, SFN311 etc. Addendum (Chinese)

WV-SW397, SFN311 etc. Addendum (Chinese)

Added to Compatible SDXC memory cards
WV-SW598, WV-SFN310 etc. Addendum

WV-SW598, WV-SFN310 etc. Addendum

To prevent unintended camera access by unkown party

Close