3Basic settings

3.1Configure this product

This section describes the procedure for setting up an AI processing relay application from the state of 2　Preparation.
1.
Displays the configuration screen for iCT's extension software.
①
Start iCT and click on "Ext. Software Management" in the menu on the left side.
②
Click "App. Settings".
③
Click on the tab "AI Processing Relay(Cam.2-)" at the top of the device list.
④
Check the cameras for which you want to install the extension software from the device list.
⑤
Click "Setting/Confirmation".
2.
The detailed settings screen of the Extension Software will be displayed. Scroll through the menu on the left to the "AI Processing Relay CamX Vx.xx" item.
In the following descriptions, the settings for AI Processing Relay cam2 are described. Please set the setting items according to your environment.
3.
Displays the browser settings screen.
①
Click "AI Processing Relay cam2 Vx.xx" from the left side menu of iCT's detailed settings screen.
②
Click the "Display" button on the right side menu.
4.
Enter information for a non-AI camera.
-
Non-AI camera username
Enter the username that has been set for the non-AI camera.
Default setting: blank
-
Non-AI camera password
Enter the camera password that has been set for the non-AI camera.
Default setting: blank
-
Protocol
Select the protocol used to access the non-AI camera from this product.
Default setting: HTTP
-
Non-AI camera IP address
Enter the IP address assigned to the non-AI camera.
Default setting: blank
-
Non-AI camera port number
Enter the port number of the protocol to be used for the non-AI camera.
Default setting: blank
-
HTTP JPEG stream URL
Enter the command to receive the MJPEG data from the non-AI camera.
Enter the command after the IP address of the camera.
Do not enter a leading "/". The leading "/" will be automatically completed by this product.
In the case of a multi-sensor camera, please include the channel specification in the command.
Default setting: blank

Example: i-PRO camera (single-lens camera)
cgi-bin/mjpeg?stream=1&framerate=5
-
Multi-directional cameras No.
If the non-AI camera is a multi-sensor camera, enter the camera number of the multi-sensor camera, specified as a number from 1~4. If the non-AI camera is a monocular camera, enter 1. The information entered in this field is used when connecting to the i-PRO Active Guard.
Default setting: 1
- Enter the information for a non-AI camera, not the information for the new X series cameras, in the settings section of this product.
5.
Click the "Set" button
6.
An alert will appear asking you to enter a username and password. Enter the username and password for a non-AI camera and click the "Sign in" button.
7.
Confirm that the non-AI camera video is displayed in Result > Received Image. The resolution and frame rate of the video actually received will be displayed in the "Resolution" and "Framerate" fields.
Follow the same procedure for AI Processing Relay Cam3 and AI Processing Relay Cam4.
Do not close this browser window until you have completed the settings for 3.2　Configure extension software that work with this product.

3.2Configure extension software that work with this product

1.
Displays the configuration screen for iCT's extension software.
①
Start iCT and click on "Ext. Software Management" in the menu on the left side.
②
Click "App. Settings".
③
Click on the tab "AI Processing Relay(Cam.2-)" at the top of the device list.
④
Check the cameras for which you want to install the extension software from the device list.
⑤
Click "Setting/Confirmation".
2.
The detailed settings screen for the extension software will be displayed. Scroll through the menu on the left to display the extension software items. The following items are displayed in the "Ext. software" section
A: Extension software for camera 1
B: Extension software for cameras 2, 3 and 4
Please refer to the manual of each extension software to set up the software.
The images of non-AI cameras (Camera2, Camera3, and Camera4) are not displayed on the configuration screen of the software for Camera2, 3, and 4. If you need to make settings while viewing the images, click the link (C in the figure below) displayed on the iCT screen and make settings on the browser's settings screen.
An alert may appear when opening the extension software screen. Enter the username and password of the camera to be linked to the alert. The live image of the linked camera will be displayed on the configuration screen of the extension software.
The live image of the non-AI camera will appear in the browser settings screen of the extension software. If the video does not appear on the browser settings screen, press the "F5" key to reload the browser screen.
For the AI Scene change detection application, the video from non-AI cameras Camera2, Camera3, and Camera4 will appear on the iCT configuration screen. If the images are not displayed, please configure the AI processing relay settings.
- The username and password for the alert must be the username and password of the camera to be linked, not the username and password of the new X series camera.
- AI-VMD Mode selection should be set to "Normal angle mode".
- iCT does not display the live image of Non-AI camera. 
  C : Please set the area settings, etc. from the link displayed in iCT.
- "Detailed setting" > "AI-VMD Information addition" in the AI-VMD application is set to Off.
- When the extension software is used with an AI processing relay application, the frame information of the detection results will not be displayed on the camera's live screen or in the iCT.
- The schedule settings for Camera 1 to Camera 4 of the AI Processing relay application and the linked extension software should always be set to On.
- It is recommended that the "Alarm" > "Camera action on alarm" setting item in the new X series cameras be set to Off.

3.3Configure i-PRO Active Guard

Refer to the i-PRO Active Guard manual for i-PRO Active Guard settings. Below we describe how to register the extension software that works with the AI processing relay application to the i-PRO Active Guard.
1.
Click "Camera Registration".
2.
Select "Add" - "AI Processing Relay App".
3.
Enter the IP address and authentication information for the new X series camera, and click "Check". Confirm that the non-AI camera appears in the list and click "Save".
4.
Click "Restart" to restart the i-PRO Active Guard server.
The following settings must be made in advance.
- 3.1　Configure this product
- Register non-AI cameras to video surveillance software

3.4Configure i-PRO Active Guard for VMS to receive AI-VMD and AI Occupancy Detection alarms

If you use Genetec / Milestone VMS, you need to configure the following settings to notify alarms. i-PRO Active Guard will notify Genetec / Milestone VMS of the AI-VMD and AI Occupancy Detection alarms by making the following settings. If you use Video Insight VMS, you do not need the following settings.
- When using Genetec / Milestone with i-PRO Active Guard / WV-ASM300UX with i-PRO Active Guard, please use the new X series camera with "Alarm" > "Notification" > "TCP alarm notification" turned off.
1.
Open i-PRO Active Guard's VMS server screen and press the "Add" button.
2.
Press the "Test" button after entering the VMS information. When "Success" is displayed, press the "Save" button.
-
Type
Select Genetec Security Center or Milestone XProtect.
-
IP address
Enter the IP address of Genetec Security Center or Milestone XProtect.
-
WEB API Port
Enter the port number of the Genetec Security Center or Milestone XProtect.
-
Notification Port (Milestone XProtect only)
Enter the Milestone XProtect notification port number.
-
SSL
Select On to enable SSL connection or Off to disable SSL connection.
-
User Name
Enter the User Name for Genetec Security Center or Milestone XProtect.
-
Password
Enter your Genetec Security Center or Milestone XProtect password.
3.
The configured VMS appears on the VMS Server screen.
4.
Check the Alarm of AI Processing relay app in the Notification column. i-PRO Active Guard will notify VMS of AI-VMD and AI Occupancy Detection alarms.