1. Home
  2. Surveillance
  3. Partners
  4. Video Management System Partners
  5. Genetec
  6. i-PRO AI-VMD in Genetec RSA Surveillance Plugin

 i-PRO AI-VMD in Genetec RSA Surveillance Plugin

Last updated: December 2025

 


The Genetec RSA Surveillance Plugin provides the following functionalities:

  • Detects intrusions into designated areas and displays target icons and tracking paths on the map.
  • Triggers events and alarms upon target detection.
  • Tracks and monitors target movement within RSA zones.

Scenario: This page outlines the procedures for configuring and operating i-PRO AI-VMD using the Genetec RSA Surveillance Plugin.

For details on supported tracking systems in the RSA Surveillance Plugin, refer to the following device list:
Genetec RSA Surveillance Technology Partners and Supported Device List.

　1. System Configuration Procedure
　2. Operational Verification Procedure

 

 

1. System Configuration Procedure　

1.1 Pre-Configuration

1.1.1 Camera-Side Configuration

1. AI-VMD Installation and Configuration
　Download and install the AI-VMD application.
　Note: Use AI-VMD version 3.80 or later.

2. AI-VMD Settings
　Refer to AI-VMD for Genetec for detailed.
4. Execute steps 1.1 to 1.3 under [1. Camera Settings] in the AI-VMD for Genetec Configuration Guide.
    Configure the detection area, detection object, and detection mode in the setup tool.
5. Execute the camera position settings in 1.4. Detail setting of the AI-VMD for Genetec Configuration Guide.
    Open [Detail setting] > [Latitude / longitude sending settings] and set the following:

  • Latitude / longitude sending settings
  • Camera location(Latitude)
  • Camera location(Longitude)
  • Camera location(Azimuth)
  • Camera height

 

Note: Please enter exact information.
・When entering the [Latitude/Longitude of the center of the angle of view], make sure to set them using the live camera view.​
・For PTZ cameras, you do not need to consider the camera’s Pan/Tilt directions, as the camera will calculate the values
based on the current Pan/Tilt information.​
・Please ensure that when entering the value, the center of the screen clearly shows the actual floor surface.
If there are any objects obstructing the view of the floor, the exact position cannot be determined.
・After setup, confirm the detection result by having a person stand at the center.

Recommendation for the center adjustment

Recommended​:
1. Ensure the center of the live camera view shows the floor​
2. At least 5 meters away from the camera position​

 

Not Recommended​:
1. Having objects obstructing the floor view at the center​
2. Less than 5 meters away from the camera position​

 

1.1.2 Genetec-Side Configuration

1. Adding i-PRO Driver to RSA
　Refer to Adding i-PRO Driver to RSA Guide for detailed.
2. Camera Registration
　Refer to Camera Registration.

1.2 Genetec Security Center Configuration

1. Creating a Georeferenced Map
　Refer to Georeferenced Map Configuration Guide for detailed.
2. Creating an RSA Zone
　Refer to RSA Zone Creation Guide for detailed.
3. Defining RSA Zones
　Refer to RSA Zone Definition Guide for detailed.
4. Adding Objects to the Map
　Refer to Object Addition Guide for detailed. 

Note: Ensure that the latitude and longitude values of map objects exactly match the camera settings in Genetec.
To avoid discrepancies, copy and paste the values directly.

Genetec side:

 

Camera side:
Camera Browser Configuration
Configure Camera Location settings to match those in Genetec.

 

2. Operational Verification Procedure

2.1 Verification via Maps

1. Open [Security Desk] > [Tasks] > [Maps].
2. In the Maps task, select the relevant map.
3. Right-click the RSA zone and set the status to [Armed].

 

RSA Target Tracking:
When an intrusion is detected, a target icon and tracking path are displayed on the map.
Target Types (Icons): Person, Vehicle, Unknown, etc.

 

 


Genetec Security Center: 5.12.2.0 / Driver Pack 12.6
Genetec Security Center Plugins-RSA: 5.2.40.0
Genetec Inter-System Gateway: 1.3.12
Supported OS: Windows 11 Pro