7Making common settings for radar and camera

7.1Setting for the Angle of Installation Error Detection

➣

Live image pages settings pane>Clicking on the [Installation angle abnormality detection] tab. You can set up the setting for error detection at the installation angle related to the radar.

7.1.1Set the angle of view registration of the radar screen

1.

Use [Angle of view registration] to set the angle of view registration.

・

Clicking [Execute] registers the current angle of view as normal.

7.1.2Set the angle of view on the radar screen

1.

Use [Angle Setting] to set the angle of view display.

・

The position of the camera can be corrected while checking the deviation from the position when the installation angle is registered.

7.2Set radar impact detection

Sets the shock detection for Security Radar.

➣

Live image pages settings pane>[Detailed setting]>[Detailed setting]>[Set]>Advanced Menu>[Alarm]>Clicking [Impact Detection] in [Impact Detection Alarms] on the [Alarm] tab. The setting page is displayed.

1.

Set [Shock Detection].

2.

Set the [Detection Level].

3.

Press [Set] to save the settings.

7.3Setting Recording (SD Memory Card)

7.3.1Inserting an SD Memory Card

1.

SD remove the cover

2.

Insert the microSD memory card into the slot

[Notice]

・Use a SD memory card that has been formatted on the digital piano.

[Important]
・To remove the SD Memory Card, [Basic] of the Advanced Menu..>On the [SD memory card] tab. Choose [SD memory card] as the [No]. Then remove the SD memory card.

7.3.2Recording with a SD Memory Card

Set the scheduled event type to [SD memory recording] to record SD. The following describes the steps when [Save trigger] is set to [Manual save].
For how to install a SD card, refer to the following:
→7.3.1　Inserting an SD Memory Card

➣

Live image pages settings pane>[Detailed setting]>[Detailed setting]>Advanced Menu>[Basic]>Clicking [SD memory card] displays the settings page.

(1)

Selecting Streams for [Recording format]

(2)

Select [Save trigger] and select [Set].

(3)

Click [Live] in the upper left corner and click the camera control panel button.

・

The camera control panel is displayed.

(4)

By clicking [Start] in the [Rec. on SD]

・

Recording to the SD memory card starts manually.

・

Recording can be stopped by clicking [Stop]. After stopping, you can resume recording by clicking [Start].

7.3.3Playing back images stored on a SD memory card

You can play back images stored on a SD memory card.

➣

Live image pages Camera-Control Panel>Clicking [Log/Play] displays the log list.

1.

Open Live image pages and press the camera control panel button.

2.

By clicking [Start] in the [Log/Play]

・

The log list display screen is displayed in a separate window.

3.

Select the recording date and time displayed below the [Time].

・

The playback page is displayed, and the saved image is played back.

7.4Set the event

You can set the operation of an area, obstruction to the radar or camera, alarm for detecting sound, operation when an alarm is detected, etc.

➣

Live image pages settings pane>[Detailed setting]>[Detailed setting]>[Set]>Advanced Menu>[Easy Setup]>Clicking [Event action] displays the configuration page.

[Reference]

・See the Security Radar documentation for instructions on setting up events.

・For more information about setting up Internet publishing, see the Security Radar documentation.

7.4.1Detecting object Motion

When an alarm occurs, the specified camera operation is performed. An alarm has a pattern that is detected when movement in a specified area is detected or when interference occurs in the camera.

➣

Live image pages settings pane>[Detailed setting]>[Detailed setting]>[Display]>Advanced Menu>Clicking [Alarm] displays the settings page.

[Reference]

・For more information about all alarms, see the Security Radar documentation.

7.4.1.1Set an area to detect the movement of an object.

Use the motion detection function using images to set the area for detecting motion of an object.

1.

Drag in the image to set the area.

・

Areas can be set in order.

2.

Adjust the [Detection area] and [Detection sensitivity] with the slider bar, then press [Set].

7.5Increase the security of communications

Configuring HTTPS encrypts access to the cameras and increases the security of communications.

・

For details on how to set HTTPS (pre-installed), refer to the supported videos below.

・

For information on how to set the HTTPS (CA certificate), refer to the supported videos below.

7.6Set the image stream

7.6.1About Stream Settings

Specify whether streaming should be performed, whether the compression method is H.265 or H.264, the Image capture size and image quality, and how the streaming should be performed.

➣

Live image pages settings pane>This is done in the [Stream numbers] tab.. H.265 images and H.264 images are streamed in the [Stream numbers] section of the [Stream numbers].

・

For information on image compression methods, see the following:
→6.3.3　Reducing Data Capacity with Smart Coding

・

For information on how to deliver, see the following:
→6.3.2　Distribution volume control (bit rate)

・

For details on each setting method, refer to the user manual.

7.6.2Distribution volume control (bit rate)

There are the following types of delivery modes for stream delivery volume control (bit rate), and they are set according to the case. You can also use smart coding, such as [Smart VIQS], to reduce the volume. For information about controlling the delivery of streams, see the following: For details, refer to the user manual.
→6.3.3　Reducing Data Capacity with Smart Coding

・

Constant Bit Rate :
Delivers H.265 (or H.264) images at the bitrate set in [Max bit rate (per client) *].

・

Variable bit rate :
Delivers H.265 (or H.264) images at the frame rate set in [Frame rate*] while maintaining the image quality level set in [Quality]. At this time, the bit rate is distributed with a variable value within the maximum bit rate set in [Max bit rate (per client) *]. The recording capacity varies depending on the [Quality] setting and the object status.

・

Frame rate specification:
Delivers H.265 (or H.264) images at the frame rate set in [Frame rate*].

・

Best effort delivery:
Depending on the bandwidth of your network, you can distribute H.265 (or H.264) images at varying bit rates, up to the maximum bit rate set in [Max bit rate (per client) *].

7.6.3Reducing Data Capacity with Smart Coding

Smart coding is a data-compression technique that reduces the amount of compression to sharpen human faces, increases the amount of compression in the background, or optimizes the amount of compression by object.

This image is an image. It differs from how the screen is actually viewed.

➣

Live image pages settings pane>[Detailed setting]>[Advanced settings page] for [Detailed setting]>[Image], or [Image/Audio] in the Advanced menu on the left>Clicking [Image] brings up the Smart Coding Settings window.

[Auto VIQS]

Keeps the image quality of the part that the object (head, person, vehicle, or two-wheel) is shown at a high quality.

[GOP control]

You can reduce the amount of data.

[Notice]

・The setting on the radar side does not show the smart coding items.

7.7Detect data tampering

If tampering detection is set, data on the SD memory card can be detected by the dedicated software. If the data on the memory card is tampered with.
For information on how to configure tampering detection, refer to the following supporting video:
→Support video

7.8Setting the Image capture size and Frame Rate

➣

Live image pages settings pane>[Stream numbers] tabbed page>Set in the [Image Capture Mode] of the [Common].

[Notice]

・For details on the settings and frame rates, refer to the user manual.

7.9Record sound

Live image pages settings pane>[Detailed setting]>[Detailed setting]>Advanced settings on the left
New [Basic]>Clicking [SD memory card] displays the configuration page.

You can set to record audio data when recording SD.

1.

Select whether to record audio in the SD recording setting window.

・

[On] : Saves audio to a movie (MP4 format).

・

[Off] : Audio files are not saved in MP4 format.