7[Easy Setup] to use easy setting

The following settings can be made on the easy setting page.

・Publish camera images on the Internet


・Sets event operation such as recording to SD Memory Card by schedule/alarm.


The easy configuration pages consist of the [Easy installation], [Internet], and [Event action] tabs.
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


[Note:]

・Dual mode is not supported.


・For how to adjust the camera orientation and angle, refer to the "Operation Manual Installation".


・To automatically adjust the camera, set the vertical (TILT) angle of the camera to 80 degrees.


When the [Easy installation] tabs on the easy setting pages are clicked, the instructions for setting the cameras are displayed.
1
Select the method in which the camera is installed.
[Install on a ceiling]:
Select this when the camera is placed on the ceiling.
[Install on a wall (horizontal direction)]:
Select this when the camera is placed horizontally on the wall.
[Install on a wall (vertical direction) Install with the right pipe (Camera 1 is on the upper side)]:
Select this if the camera is installed vertically on a wall with Camera 1 facing up.
[Install on a wall (vertical direction) Install with the left pipe (Camera 2 is on the upper side)]:
Select this if the camera is installed vertically on a wall with Camera 2 facing up.
[Next]Button:
Go to the next display.
2
Check the actual display. Fine-tune the screen as required.
[Display Layout]:
The image display position can be specified.
[Left/right placement]: The screen will be left-to-right.
[Up/down placement]: The screen is positioned up and down.
Press [Execute] to refresh the window in the selected alignment.
[Switch the camera display position]:
Press [Execute] to change the displayed window.
[Image rotation]:
Rotate the displayed image.
[Zoom adjustment]:
Zoom is adjusted.
[Back]Button:
Go back to a previous screen.
[Set]Button:
Confirms made selections.
Click the [Internet] tab for easy setting. Refer to the table below for how to display and operate the setting menu.
5.1 How to display
5.2 How to operate
This is to configure the UPnP (Automatic Port Forwarding), DDNS, and Internet Recommendation settings that are required to publish the camera on the Internet.
[UPnP(Auto port forwarding)]
You can configure [On]/[Off] to use the router's port forwarding capability.
To use the Automatic Port Forwarding feature, the router you use must be UPnP-enabled and UPnP enabled.
[Note:]

・Automatic port forwarding may change the port number. If this is changed, the port number of the camera registered on the PC or recorder must be changed.


・The UPnP feature can be used to connect a camera to an IPv4 network. IPv6 is not supported.


・To verify that auto-port forwarding has been configured correctly, click on the [Status] tab on the Maintenance page and make sure that the [UPnP] status is [On].
16.3 [Status] for checking the status
If [On] is not displayed, please read [Cannot access cameras from internet] in "Trouble!?"
18.2 Trouble!?


・If you change the [UPnP(Auto port forwarding)] settings, the [UPnP] on the [Advanced] tabs of the network pages will also change.


・If the live screen or configuration screen is not displayed correctly, such as when replacing the routers to be used, set [UPnP(Auto port forwarding)] to [Off] once and then set it to [On] again.


[Area]
Select the region where the camera is installed.
[Global]/[Japan]
[Note:]

・Select [Japan] when using cameras in Japan. The [Viewnetcam.com] services displayed when [Global] is selected are not accessible from within Japan.


・[Indoor PTZ] [Viewnetcam.com] servicedoes not appear even if you select [Global].


[Service]
Select [Viewnetcam.com]/[Off] to use the [Viewnetcam.com] services in the DDNS. After you set up the Net, click [Go to MIEMASUNET Registration page] to open the Register [Viewnetcam.com] Services window in the new window. After that, proceed with the registration according to the screen.
For more information, see [With [Viewnetcam.com] services] or the [Viewnetcam.com] website (http://www.viewnetcam.com/).
14.4.1 With [Viewnetcam.com] services
[Note:]

・If you change the [DDNS] settings, the [DDNS] on the [Advanced] tabs of the network pages will also change.


[Recommended network setting for internet]
Set the recommended settings for publishing the camera on the Internet. When [Set] is clicked, the dialog box displays the changes in the settings for the following settings: Click OK after checking.
Compact Dome cameras (X/S series, Image capture size: 4MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:QVGA/ 320x180


・[Stream(1)] ・ [Stream(2)] ・ [Stream(3)]
[
Delivery mode]: best effort delivery
[Frame rate]: 30 fps
[Max bit rate (per client) *] :1024 kbps


・[Stream(1)]
[Image capture size]:2560x1920/2560x1440


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :VGA/ 640x360


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Compact Dome cameras (X/S series, Image capture size: 2MP),New X Fixed Cameras(Image capture size: 2MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[
Image capture size]:QVGA/ 320x180


・[Stream(1)]
[
Delivery mode]: best effort delivery
[Frame rate]: 30/ 25 fps(When [Image capture mode] is [(60/ 50 fps)] mode: 60/ 50 fps)
[Max bit rate (per client) *] :1024 kbps


・[Stream(2)] ・ [Stream(3)] ・ [Stream(4)]
[
Delivery mode: best effort delivery
[Frame rate]: 30 fps(When [Image capture mode] is [(60/ 50 fps)] mode: 10/ 8.3 fps)
[Max bit rate (per client) *] :1024 kbps


・[Stream(1)]
[
Image capture size] :1280x960/ 1280x720


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :VGA/ 640x360


・[Stream(4)]
[Image capture size] :QVGA/ 320x180


[Network] tabs on network pages

・[IPv6/v4 Common
[
Maximum RTP packet size: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Compact Dome cameras (U series, Image capture size: 4MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:QVGA/ 320x180 (When [Image capture mode] is [16:9(30/ 25fps)2688x1520] mode: 640x360)


[Stream(1)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)][16:9 mode(2688x1520 30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)][16:9 mode(2688x1520 25fps mode)]: 25fps
When [Image capture mode] is [4:3 mode(15fps mode)]: 15fps
When [Image capture mode] is [4:3 mode(12.5fps mode)]: 12.5fps


 [Max bit rate (per client) *] :1024 kbps

[Stream(2)] ・ [Stream(3)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 25fps
When [Image capture mode] is [4:3 mode(15fps mode)]: 15fps
When [Image capture mode] is [4:3 mode(12.5fps mode)]: 12.5fps
When [Image capture mode] is [16:9 mode(2688x1520 30fps mode)]: Off
When [Image capture mode] is [16:9 mode(2688x1520 25fps mode)]: Off


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size]:1280x960 (When [Image capture mode] is [4:3(15/ 12.5fps)] mode: 2048x1536)/ 1920x1080


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :QVGA/ 320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Compact Dome cameras (U series, Image capture size: 2MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:QVGA/ 320x180


[Stream(1)] ・ [Stream(2)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 25fps


 [Max bit rate (per client) *] :1024 kbps

[Stream(3)] ・ [Stream(4)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]: 25fps
When [Image capture mode] is [16:9 mode(30fps mode)]: 5fps
When [Image capture mode] is [16:9 mode(25fps mode)]: 6.25fps


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size]:1280x960/ 1280x720


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :QVGA/ 320x180


・[Stream(4)]
[Image capture size] :QVGA/ 320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)



New X Fixed Cameras(Image capture size: 8MP,Image capture size: 6MP,Image capture size: 5MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:2560x1440


・[JPEG(2)]
[Image capture size]:640x360


・[Stream(1)]
[
Delivery mode]: best effort delivery
[Frame rate]: 5/ 4.2 fps(When [Image capture mode] is [(60/ 50 fps)] mode: 60/ 50 fps)
[Max bit rate (per client) *] :1024 kbps


・[Stream(2)] ・ [Stream(3)] ・ [Stream(4)]
[
Delivery mode]: best effort delivery
[Frame rate]: 15/ 12.5 fps(When [Image capture mode] is [(60/ 50 fps)] mode: Off)
[Max bit rate (per client) *] :1024 kbps


・[Stream(1)]
[Image capture size]:2560x1440


[Stream(2)] ・ [Stream(3)]
[Image capture size] :640x360


・[Stream(4)]
[Image capture size] :320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Corner cameras
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:QVGA/ 320x180


[Stream(1)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 5fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 4.2fps


 [Max bit rate (per client) *] :1024 kbps

[Stream(2)] ・ [Stream(3)] ・ [Stream(4)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 15fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 12.5fps


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size]:2560x1920/ 2560x1440


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :VGA/ 640x360


・[Stream(4)]
[Image capture size] :QVGA/ 320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Rapid PTZ Cameras (X/S Series, Image capture size: 2MP), Multi-directional + PTZ (PTZ part)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:QVGA/ 320x180


[Stream(1)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(15fps mode)]: 15fps
When [Image capture mode] is [4:3 mode(12.5fps mode)]: 12.5fps
When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 25fps
When [Image capture mode] is [16:9 mode(60fps mode)]: 60fps fixed
When [Image capture mode] is [16:9 mode(50fps mode)]: 50fps fixed


 [Max bit rate (per client) *] :1024 kbps

[Stream(2)] ・ [Stream(3)] ・ [Stream(4)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [4:3 mode(15fps mode)]: 15fps
When [Image capture mode] is [4:3 mode(12.5fps mode)]: 12.5fps
When [Image capture mode] is [4:3 mode(30fps mode)]/ [16:9 mode(30fps mode)]: 30fps
When [Image capture mode] is [4:3 mode(25fps mode)]/ [16:9 mode(25fps mode)]: 25fps
When [Image capture mode] is [16:9 mode(60fps mode)]: 10fps
When [Image capture mode] is [16:9 mode(50fps mode)]: 8.3fps


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size]:1280x960/ 1280x720


・[Stream(2)]
[Image capture size] :VGA/ 640x360


・[Stream(3)]
[Image capture size] :VGA/ 640x360


・[Stream(4)]
[Image capture size] :QVGA/ 320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Rapid PTZ Cameras (X/S series, Image capture size: 8M (4K)), Indoor PTZ cameras (Image capture size: 8M (4K)), Image capture size: 6MP)
[Image] tabs for video and audio pages

・[JPEG(1)]
[Image capture size]:320x180


[Stream(1)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [16:9 mode(30fps mode)]: 5fps
When [Image capture mode] is [16:9 mode(25fps mode)]: 4.2fps


 [Max bit rate (per client) *] :1024 kbps

[Stream(2)] ・ [Stream(3)] ・ [Stream(4)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [16:9 mode(30fps mode)]: 15fps
When [Image capture mode] is [16:9 mode(25fps mode)]: 12.5fps


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size] :2560x1440


・[Stream(2)]
[Image capture size] :640x360


・[Stream(3)]
[Image capture size] :640x360


・[Stream(4)]
[Image capture size] :320x180


[Network] tabs on network pages

・[IPv6/v4 Common]
[Maximum RTP packet size]: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Multi-directional camera
[Image] tabs for video and audio pages

・[JPEG]
[
Image capture size : 320 x 180 (when Image capture mode is not in Quad/Dual mode)/640 x 360 (when Image capture mode is in Quad/Dual mode)


[Stream(1)] ・ [Stream(2)]
[Delivery mode]: best effort delivery


 [Frame rate]: When [Image capture mode] is [5 megapixels [4:3](15fps mode)]/ [5 megapixels [16:9](15fps mode)]: 15fps
When [Image capture mode] is [5 megapixels [4:3](12.5fps mode)]/ [5 megapixels [16:9](12.5fps mode)]: 12.5fps
When [Image capture mode] is [5 megapixels [4:3](15fps Quad mode)]/ [5 megapixels [16:9](15fps Quad mode)]: 15fps
When [Image capture mode] is [5 megapixels [4:3](12.5fps Quad mode)]/ [5 megapixels [16:9](12.5fps Quad mode)]: 12.5fps


 [Max bit rate (per client) *] :1024 kbps

・[Stream(1)]
[Image capture size] :2560x1440


・[Stream (2)
[Image capture size] :640x360


[Network] tabs on network pages

・[IPv6/v4 Common
[
Maximum RTP packet size: Limited (1280 bytes)
[HTTP max segment size(MSS)]: Restricted (1280 bytes)


Select the [Event action] tabs on the easy setting pages. Refer to the table below for how to display and operate the setting menu.
5.1 How to display
5.2 How to operate
Here, the contents of the current setting are displayed.
In event operation, the event operation can be set for SD schedule recording, regular transmission of FTP/SFTP, and alarm detection. When the settings are complete, press [Next] to proceed.
The configuration flow is as follows.
[Note:]

・[FTP/SFTP periodic image transmission] can be selected only for models with FTP/SFTP features.


・Refer to the catalog specifications for the functions installed in each model.


・Clicking [Next] saves the settings in the window.


Event operation flow
Event type setting
Select the desired operating conditions.
Alarm
7.3.2 Alarm: Sets terminal and operation detection (alarm setting screen)
Schedule
7.3.9 Schedule: Setting FTP/SFTP Periodic Transmission (FTP/SFTP Periodic Transmission Setting Screen)



Terminal/VMD/SCD/Audio detection/Impact detection/Casing open detection






Event operation setting
Set the operating conditions selected in the event type setting.
FTP/SFTP transfer
7.3.4 Alarm: Setting details of image transfer or recording conditions
SD recording
7.3.4 Alarm: Setting details of image transfer or recording conditions
SD recording
H.265/H.264
7.3.8 Schedule: Set SD recording (Movie recording setting screen)
Regular transmission of FTP/SFTP
7.3.9 Schedule: Setting FTP/SFTP Periodic Transmission (FTP/SFTP Periodic Transmission Setting Screen)




Event operation setting
Set the operating conditions selected in the event type setting.
Recording condition setting
Recording condition setting
Image transfer method setting



FTP/SFTP settings





Alarm output (terminal)



Mail setting
Schedule setting


Completion
Completion
[Note:]

・[MULTI] There is no FTP/SFTP function.


Here, select the type of event.
[Trigger]
[Alarm]:Select this to set the alarm detection.
[Schedule] :[Select this when you want to [FTP/SFTP periodic image transmission] SD-Record.

[Note:]

・[FTP/SFTP periodic image transmission] can be selected only for models with FTP/SFTP features.


・Refer to the catalog specifications for the functions installed in each model.


[SD memory card format]
To format the SD Memory Card, press [Execute].
Clicking [Execute] displays the [Format] confirmation window.
Press the [OK] button to start formatting.
When the [Format] Completion window is displayed, press x.
[Important]

・When formatting is performed, all data stored on the SD Memory Card are deleted.


・Do not turn off the computer during formatting.


[Next] buttons
Select [Alarm] and press [Next] to open the Alarm Settings window.
7.3.2 Alarm: Sets terminal and operation detection (alarm setting screen)
Select [Schedule] and press [Next] to open the Schedule Type Settings window.
7.3.7 Schedule: Set SD recording or FTP/SFTP periodic transmission (Schedule type setting screen)
This section sets the operation when an alarm is detected.
Corner cameras
Alarm
[Terminal 1]
Set the operation of terminal 1.

[Off]:Terminal function is not used.


[Alarm input(TRM1)]:Terminal alarm input is received.


 ・[Close]:When the terminal status changes to [On], an alarm is detected.
[Open]:When the terminal status changes to [Off], an alarm is detected.
[Close(Continue)]:When the terminal status changes to [On], an alarm is detected. When the terminal status is [On], the alarm is detected periodically at intervals of no alarm detection time.
[Open(Continue)]:When the terminal status changes to [Off], an alarm is detected. When the terminal status is [Off], the alarm is detected periodically at intervals of no alarm detection time.


[Black & white input]:Receives black-and-white selector input. (When the input is [On], the input is switched to black and white)


[Auto time adjustment]:Time setting by terminal input is accepted. When the signal is input, set to 00 minutes 00 seconds if the time difference from the normal time (00 minutes per hour) is 29 minutes or less. In the case of returning the time less than 5 seconds during SD recording, the time is not changed. Selecting Auto Time Adjustment displays the pull-down menu for short circuit and release selection.


 ・[Close]:When the terminal status changes to [Close], the automatic time adjustment is performed.
[Open]:When the terminal status changes to [Open], the automatic time adjustment is performed.


[Terminal 2]
Set the operation of terminal 2.

[Off]:Terminal function is not used.


[Alarm input (TRM2)]:The alarm input is received.


[Short circuit]:When the terminal status changes to [On], an alarm is detected.
[Open]:When the terminal status changes to [Off], an alarm is detected.
[Short circuit (Continued)]:When the terminal status changes to [On], an alarm is detected. When the terminal status is [On], the alarm is detected periodically at intervals of no alarm detection time.
[Open (continued)]:When the terminal status changes to [Off], an alarm is detected. When the terminal status is [Off], the alarm is detected periodically at intervals of no alarm detection time.


[Alarm Output]:Alarm outputs according to the setting in [Output terminal].


12.2 [Alarm] for setting the output terminal
[Terminal 3]
Set the operation of terminal 3.

[Off]:Terminal function is not used.


[Alarm input (TRM3)]:The alarm input is received.


[Short circuit]:When the terminal status changes to [On], an alarm is detected.
[Open]:When the terminal status changes to [Off], an alarm is detected.
[Short circuit (Continued)]:When the terminal status changes to [On], an alarm is detected. When the terminal status is [On], the alarm is detected periodically at intervals of no alarm detection time.
[Open (continued)]:When the terminal status changes to [Off], an alarm is detected. When the terminal status is [Off], the alarm is detected periodically at intervals of no alarm detection time.


[Aux output]:AUX output is performed. The [AUX] buttons appear on the live picture pages.


[VMD alarm]
On:If the motion detection area is not set, the entire area is set. To set the operation detection area, use the [VMD area] tab on the alarm page.
12.6 [VMD area] to set the motion detection area
[Off]:Disables all operation detection status.

[Scene change detection (SCD) alarm]
[
On]:If the disturbance detection area is not set, the entire area is set. To set up the undesired detection area, use the [SCD area] tab on the alarm page.
12.7 [SCD area] to set up undesired detection
[Off]:Disables all disturbance detection conditions.

[Audio detection alarm]
[
On]:Use the sound detection alarm. All AI sounds are recognized.
12.9 [Audio detection] for setting sound detection
[Off]:Sound detection alarm is not used.

[Impact detection alarm]
[On]:Use the impact detection alarm. Impact detection is recognized.
12.10 [Impact detection] for setting impact detection
[Off]:Impact detection alarm is not used.

[Casing open detection alarm]
[On]:Use the opening detection alarm. Opening detection is recognized.
12.11 [Casing open detection] for setting opening detection
[Off]:Opening detection alarm is not used.

[Alarm deactivation time]
Sets the time when the alarm is detected and the detection operation is not executed. For example, if you set up an e-mail notification to a mobile terminal or a tablet terminal using an alarm, this setting prevents you from sending too much e-mail.
5-[600 seconds]
[Note:]

・Alarm detection time is managed for each alarm type. For example, the operation detection alarm is detected even when the alarm of terminal alarm 1 is not detected.


Alarm linkage operation

[Terminal alarm 1]
Select the action to be interlocked when terminal alarm 1 is detected from the following. This can be set when [Terminal 1] of the alarm is set to [Alarm input(TRM1)].
[Off]:Interlock operation is not performed even if terminal alarm 1 is detected.
1~256:When the preset position registered in advance is selected, the watch moves to the preset position when terminal alarm 1 is detected.
[Patrol 1]:When terminal alarm 1 is detected, patrol starts.
*When Patrol 1 is not registered, it is not displayed.

[Terminal alarm 2]
Select the action to be interlocked when terminal alarm 2 is detected from the following. This can be set when [Terminal 2] of the alarm is set to [Alarm input(TRM2)].
[Off]:Interlock operation is not performed even if terminal alarm 2 is detected.
1~256:When the preset position registered in advance is selected, it moves to the position when terminal alarm 2 is detected.
[Patrol 2]:When terminal alarm 2 is detected, patrol starts.
*When Patrol 2 is not registered, it is not displayed.

[Terminal alarm 3]
Select the action to interlock when terminal alarm 3 is detected from the following. This can be set when [Terminal 3] of the alarm is set to [Alarm input(TRM3)].
[Off]:Interlock operation is not performed even if terminal alarm 3 is detected.
1~256:Select the preset position registered beforehand to move to the position when terminal alarm 3 is detected.
[Patrol 3]:When terminal alarm 3 is detected, patrol starts.
*When Patrol 3 is not registered, it is not displayed.
[Note:]

・[PTZ] Only PTZ can be selected for [Camera action on alarm].


[VMD alarm]
Select the action to be linked to the alarm detected by the motion detector from the following.
[Off]:When an alarm is detected by the motion detector, interlock operation is not performed.
1~256:Selecting the preset position registered beforehand moves the watch to the position when an alarm is detected by the motion detector.
[Patrol 1]:When an alarm is detected by the motion detector, a patrol is started.
*When Patrol 1 is not registered, it is not displayed.

[Scene change detection (SCD) alarm]
Select the action to be interlocked when an alarm is detected by the undesired signal detection
from the following.
[Off]:Interlock operation is not performed even if an alarm is detected by undesired signal detection.
1~256:When the preset position registered in advance is selected, the watch moves to the preset
position when an alarm due to disturbance detection is detected.
[Patrol 1]:When an alarm is detected by the disturbance detection, a patrol is started. *When
Patrol 1 is not registered, it is not displayed.

[Audio detection alarm]
Select the action to be linked to the alarm detected by the sound detection from the following.
[Off]:The product does not perform interlocked operation even if an alarm is detected by sound detection.
1~256:When the preset position registered in advance is selected, the watch moves to the preset position when an alarm is detected.
[Patrol 1]:When an alarm is detected by sound detection, patrol is started.
*When Patrol 1 is not registered, it is not displayed.
[Next] buttons
Click the [Next] button to open the Alarm type setting window.
7.3.1 Schedule/alarm setting (event type setting screen)
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
Here, the operation to be performed when the alarm is detected is set.
[Trigger]
[FTP/SFTP Transfer]:FTP/SFTP transfers JPEG images when an alarm is generated.
[SD memory recording]:Record to SD Memory Card when an alarm is generated.
[Note:]

・[FTP/SFTP periodic image transmission] can be selected only for models with FTP/SFTP features.


・Refer to the catalog specifications for the functions installed in each model.


・[FTP/SFTP] and [[FTP/SFTP periodic image transmission]] can be operated at the same time when an alarm is generated.


・When [FTP/SFTP Transfer] and [[FTP/SFTP periodic image transmission]] are set simultaneously when an alarm is generated, [FTP/SFTP Transfer] when an alarm is generated takes precedence.


[Recording format]
When [SD memory recording] is selected in [Trigger], select the compression method for the images to be recorded from the JPEG/stream.
[Next] buttons
Select [FTP/SFTP Transfer] in [Trigger] and press [Next] to open the FTP/SFTP Transfer Settings window.
Select [SD memory recording] in [Trigger] and JPEG in [Recording format] and press [Next] to open the JPEG Record Setting window.
Select "[SD memory recording]" in "[Trigger]" and "[Recording format]" in "Streams" and press "[Next]" to open the Movie Record Setting window.
7.3.4 Alarm: Setting details of image transfer or recording conditions
[Note:]

・Clicking [Next] saves the settings in the window.


・The alarm alarm is not recorded on the SD memory card.


[Back] button
Returns to the previous screen.
Setting FTP/SFTP transfer (FTP/SFTP transfer setting screen)
In this case, FTP/SFTP transfer when alarm is detected is set.
[Note:]

・The factors displayed differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


For details on how to set up the above screen, refer to the following.
14.2.2 Configuring FTP/SFTP transmission function
[Next] buttons
Select [Alarm output] in the Alarm Settings window and press [Next] to open the Alarm Outputs dialog box.
7.3.5 Alarm: Sets output terminal.
If you do not select [Alarm output] on the Alarm Settings screen and [Next] is clicked, the Mail Settings screen is displayed.
7.3.6 Alarm: Configuring mail notification and mail server
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
Setting SD recording (JPEG recording setting screen)
The SD recording (JPEG) for alarm detection is set here.
See the [JPEG recording(Alarm)] below for instructions on how to set up the window above.
8.2 [SD memory card] for setting SD Memory Cards
[Next] buttons
Select [Alarm output] in the Alarm Settings window and press [Next] to open the Alarm Outputs dialog box.
7.3.5 Alarm: Sets output terminal.
If you do not select [Alarm output] on the Alarm Settings screen and [Next] is clicked, the Mail Settings screen is displayed.
7.3.6 Alarm: Configuring mail notification and mail server
[Back] button
Returns to the previous screen.
Set SD recording (H.265 or H.264) (Movie recording setting screen)
Here, SD recording (H.265 or H.264) at alarm detection is set.
[Audio recording]
Select whether or not to record audio data with [On] or [Off].
[On]:Audio data is saved in the movie (MP4 format).
[Off]:Audio data is not saved in movies (MP4 format).
[Note:]

・If the audio distribution mode is set to bi-directional (half duplex), the settings cannot be made.


Frame Rate
Set the frame rate of H.265 (or H.264) to be recorded.
[Note:]

・Refer to the [Frame rate*] below for the frame rate you can set and the bit rate that depends on the frame rate.
7.3.8 Schedule: Set SD recording (Movie recording setting screen)


[Pre alarm (recording) duration]
Select whether to record before alarm. Sets the time to save to the SD Memory Card.
[Off]/ [1s]/ [2s]/ [3s]/ [4s]/ [5s]/ [8s]/ [10s]/ [15s]/ [20s]/ [25s]/ [30s]/ [40s]/ [50s]/ [60s]/ [90s]/ [120s]
[Note:]

・The values that can be set depend on the resolution and bit rate of the stream to be recorded. The higher the bit rate, the smaller the maximum value that can be set as the pre-alarm time.


[Post alarm (recording) duration]
Sets the time to save to the SD Memory Card after an alarm is generated.
[10s]/ [20s]/ [30s]/ [40s]/ [50s]/ [60s]/ [120s]/ [180s]/ [240s]/ [300s]
[Next] buttons
Select [Alarm output] in the Alarm Settings window and press [Next] to open the Alarm Outputs dialog box.
7.3.5 Alarm: Sets output terminal.
If you do not select [Alarm output] on the Alarm Settings screen and [Next] is clicked, the Mail Settings screen is displayed.
7.3.6 Alarm: Configuring mail notification and mail server
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
[Note:]

・Refer to the catalog specifications for the functions installed in each model.


The alarm output is set here. This message is displayed when [Alarm output] is selected in the alarm setting window.

To set the output terminal:
For details of the settings on the screen above, refer to the following.
12.2 [Alarm] for setting the output terminal

[Next] buttons
Click the [Next] button to display the mail setting screen.
7.3.6 Alarm: Configuring mail notification and mail server
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
Here, the settings for mail are made.
[Note:]

・The factors displayed differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


For details on how to set up the above screen, refer to the following.
14.2.1 Set mail sending
[Set] buttons
Clicking [Set] completes the setting.
[Back] button
Returns to the previous screen.
Here you set the scheduling type to [SD memory recording] or [FTP/SFTP periodic image transmission].
[Trigger]
[SD memory recording]:Record H.265 (or H.264) images on the SD Memory Card at the scheduled time.
[FTP/SFTP periodic image transmission]:The JPEG image is sent to the FTP/SFTP server at the scheduled time.
[Recording format]
When [SD memory recording] is selected in [Trigger], select the streams to be recorded.
[Next] buttons
Select [SD memory recording] and press [Next] to open the Movie Record Setting window.
7.3.8 Schedule: Set SD recording (Movie recording setting screen)
Select [FTP/SFTP periodic image transmission] and press [Next] to open the FTP/SFTP Periodic Transmission Settings window.
7.3.9 Schedule: Setting FTP/SFTP Periodic Transmission (FTP/SFTP Periodic Transmission Setting Screen)
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
[Note:]

・The [Trigger] [FTP/SFTP periodic image transmission] can be selected only for models with FTP/SFTP features.


・Refer to the catalog specifications for the functions installed in each model.


・Both [FTP/SFTP periodic image transmission] and [FTP/SFTP] can be operated simultaneously when an alarm is generated.


・Selecting [SD memory recording] cancels the [FTP/SFTP periodic image transmission] setting.


Here, the schedule SD recording (H.265 or H.264) is set.
When the [Next] button is clicked after recording or setting the frame rate on the movie recording setting screen, the schedule setting screen is displayed and you can set the schedule.
1
The recording, frame rate, and SD Memory Card are overwritten on the movie recording setting screen.
[Audio recording]
You set whether to record audio data.
[On]:Audio data is saved in the movie (MP4 format).
[Off]:Audio data is not saved in movies (MP4 format).
[Note:]

・If the audio distribution mode is set to bi-directional (half duplex), the settings cannot be made.


[Important]

・When [Overwrite] is switched from [Off] to [On], the old images may be deleted to prepare for writing if there is not enough space on the SD Memory Card.


[Frame rate*]
Set the frame rate of H.265 (or H.264) to be recorded from the following.

–If [Image capture mode] is set to 30 fps:
1fps/ 3fps/ 5fps*/ 7.5fps*/ 10fps*/ 12fps*/ 15fps*/ 20fps*/ 30fps*


–If [Image capture mode] is set to 25fps:
1fps/ 3.1fps/ 4.2fps*/ 6.25fps*/ 8.3fps*/ 12.5fps*/ 20fps*/ 25fps*


–If [Image capture mode] is set to 15 fps:
1fps/ 3fps/ 5fps*/ 7.5fps*/ 10fps*/ 12fps*/ 15fps*


–If [Image capture mode] is set to 12.5 fps:
1fps/ 3.1fps/ 4.2fps*/ 6.25fps*/ 8.3fps*/ 12.5fps*


[Note:]

・When [Next] is clicked, [Transmission priority] is set to [Frame rate].


The bit rate is automatically set according to the selected resolution and frame rate. Check the [Bit Rate* per Client] settings for each stream.
[Overwrite]
You set whether to overwrite and save images when the free space on the SD Memory Card is running low.
[On]:If the free space on the SD Memory Card decreases, the old image is overwritten and saved repeatedly.
[Off]:If the SD Memory Card has no free space, the SD Memory Card stops storing data.
[Important]

・When [Overwrite] is switched from [Off] to [On], the old images may be deleted to prepare for writing if there is not enough space on the SD Memory Card.


[Next] buttons
Clicking [Next] displays the window for setting the recording schedule to the SD Memory Card.
[Back] button
Returns to the previous screen.
2
Set schedule on the Schedule Setting screen.
For details on how to set up the above screen, refer to the following.
15 [Schedule] for scheduling
[Set] buttons
Clicking [Set] completes the setting.
[Back] button
Returns to the previous screen.
[Note:]

・If [SD memory recording] is not selected in [Operation mode], no recording is performed.


Here, the FTP/SFTP periodic transmission is set.
When [Next] is clicked after periodic transmission and setting of servers on the periodic transmission setting screen, the periodic transmission schedule setting screen is displayed and the schedule for periodic transmission can be set.
[Note:]

・Only models with FTP/SFTP functions can be set.


・Refer to the catalog specifications for the functions installed in each model.


1
Settings for periodic transmission are made on the Periodic Transmission Setting screen.
For details of the settings on the screen above, refer to the following.
14.2.2 Configuring FTP/SFTP transmission function
[Set] buttons
Displayed when [FTP periodic image transmission] is [Off]. Clicking [Set] saves the settings.
[Next] buttons
Displayed when [FTP periodic image transmission] is [On]. Clicking [Next] displays the window for setting FTP/SFTP scheduled periodic transmissions.
[Note:]

・Clicking [Next] saves the settings in the window.


[Back] button
Returns to the previous screen.
2
Set the schedule for periodic transmission on the Schedule Setting screen.
For details on how to set up the above screen, refer to the following.
15 [Schedule] for scheduling
[Set] buttons
Clicking [Set] completes the setting.
[Back] button
Returns to the previous screen.
[Note:]

・If [FTP/SFTP periodic image transmission] is not selected in [Operation mode], no FTP/SFTP periodic transmission is performed.