14Networking configuration [Network]

Network pages configure network settings.
Network pages consist of the [Network] tab and the [Advanced] tab.
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


On the Network Page, press the [Network] tab. Refer to the following how to display and operate the Advanced menu.
5.1 How to display
5.2 How to operate
The following information is required to configure the network.
Check with your network administrator or Internet service provider.

・IP address


・Subnet Mask


・Default Gateway (with Gateway Server Router)


・HTTP port


・Primary server address for DNS, secondary server address (when DNS is used)


[Note:]

・Contact your network administrator for the address settings for each server.


・To connect a camera to a router and access the camera via the Internet, you must configure a separate HTTP port number for each network camera, and use the router's port forwarding features to translate addresses. For details, refer to your router's instruction manual.


・Port forwarding functions are used to convert global IP addresses to private IP addresses, such as Static IP Mascalade and Network Address Translation (NAT). This feature is configured on the router.


IPv4 network
[Network Settings]
Select how to set the IP address.
[Static]:Enter the IP address into the [IP address(IPv4)] to set the IP address.
[DHCP]:Set the IP address using the DHCP function. If you cannot obtain an IP address from the DHCP server, set the IP address to 192.168.0.10. Subsequently, if you obtain an IP address from a DHCP server, you change it to the IP address.
[Auto(AutoIP)]:Set the IP address using the DHCP function. If the DHCP server is not found, the IP address is automatically configured.
[Auto(Advanced)]:Using the DHCP function, refer to the network address information and set the unused IP address to the camera as the fixed IP address. The camera automatically determines the set IP address within the range of the subnet mask. If the DHCP server is not found, set the IP address to 192.168.0.10.
[Note:]

・If the IP address cannot be retrieved from the DHCP server in AutoIP, search for the IP address that is not used in the same network between 169.254.1.0 and 169.254.254.255 and set the IP address.


・[MULTI_PTZ] In DHCP/Auto setting (Omakase), if the DHCP server is not found, set the IP address of the PTZ camera to 192.168.0.10 and the IP address of the Multi-directional camera to 192.168.0.11.


[IP address(IPv4)]
When the DHCP function is not used, enter the IP address of the computer. Do not overlap with the IP address set on the PC or other network camera.
[Note:]

・Multiple IP addresses are not available even when the DHCP function is used. Contact your network administrator for the DHCP server configuration.


[Subnet mask]
When the DHCP function is not used, enter the subnet mask of the computer.
[Default gateway]
If you do not use the DHCP function, enter the default gateway for your computer.
[Note:]

・Multiple IP addresses are not available for the default gateway, even if you use the DHCP facility. Contact your network administrator for the DHCP server configuration.


[DNS]
Specify whether the DNS server addresses are automatically acquired ([Auto]) or manually entered ([Manual]).
When set to [Manual], you need to configure the DNS server IP addresses.
If you use the DHCP function, you can automatically obtain the DNS server address by setting it to [Auto].
Contact your system administrator for the setting.
[Primary server address], [Secondary server address]
If you use [DNS] with [Manual], enter the IP address of the DNS server.
Contact your system administrator for the IP address of the DNS server.
IPv6 network
[Important]

・When IPv6 is accessed, the stream image cannot be displayed on the live screen. If you want to display the stream image on the live screen, please access it via IPv4.


[Manual]
Configure [On] and [Off] to manually configure IPv6 addresses.
[On]:Manually enter the IPv6 address.
[Off]:IPv6 address cannot be entered manually.
[IP address(IPv6)]
If [Manual] is set to [On], IPv6 addresses must be entered manually.
Enter to avoid duplication with other devices.
[Note:]

・When connecting over a router with a manually configured IP address, enable the automatic configuration feature for IPv6 addresses using IPv6-compatible routers. Configure an IPv6 address that contains prefix information provided by IPv6-compatible routers. For details, refer to your router's instruction manual.


[Default gateway]
Enter the default gateway for the IPv6 network when the IPv6 network [Manual] is [On].
[DHCPv6]
You can configure [On]/[Off] to use the IPv6 DHCP feature.
Configure the DHCP server so that the PC and other network cameras that do not use the DHCP function do not have the same IP address. Contact your network administrator for server configuration.
[Primary DNS server address], [Secondary DNS server address]
Enter the IPv6 address of the DNS server. Contact your system administrator for the IPv6 address of the DNS server.
Common
[HTTP port]
Assign individual port numbers.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80、110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・Some ports may not be accessed by some browsers. If access is lost, use HTTPS or the i-PRO Setup Tool (iCT) to change the port number.


・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Line speed]
Select the data communication speed from the following. Normally, it is recommended to use the default [Auto].
[Auto]:The communication speed is set automatically.
[100 M‑Full]:100 Mbps full duplex
[100 M‑Half]:100 Mbps half duplex
[10 M‑Full]:10 Mbps full duplex
[10 M‑Half]:10 Mbps half duplex
[Max RTP packet size]
Set whether to limit the size of RTP packets sent from the camera when viewing camera images using RTP. Normally, it is recommended to use the [1,500 bytes] option.
If the packet size of the communication line is limited, select [Restricted (1280 bytes)]. Contact the network administrator for the maximum packet size of the communication line.
[HTTP max segment size(MSS)]
Set whether to limit the maximum segment size (MSS) sent from the camera when viewing the camera image using HTTP. Usually, it is recommended to use the default settings.
If the maximum segment size (MSS) of the communication line to be used is limited, select [1024 Byte]/[Restricted (1280 Byte)]. Contact your network administrator for the maximum segment size (MSS) of the communication line.
[Bandwidth control(bit rate)]
Select the amount of data delivered from the following.
[MULTI4][MULTI3][MULTI2S]
[Unlimited]/4096kbps/ 6144kbps/ 8192kbps/ 10240kbps/ 12288kbps/ 15360kbps/ 20480kbps/ 25600kbps/ 30720kbps/ 35840kbps/ 40960kbps/ 51200kbps/ 61440kbps/ 81920kbps/ 102400kbps/ 153600kbps
[PTZ][CompactX][CompactS][New X Fixed]
[Unlimited]/64kbps/ 128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024kbps/ 2048kbps/ 4096kbps/ 6144kbps/ 8192kbps/ 10240kbps/ 15360kbps/ 20480kbps/ 25600kbps/ 30720kbps/ 35840kbps/ 40960kbps/ 51200kbps
[MULTI2U]
[Unlimited]/128kbps/ 256kbps/ 384kbps/ 512kbps/ 768kbps/ 1024kbps/ 2048kbps/ 4096kbps/ 6144kbps/ 8192kbps/ 10240kbps/ 15360kbps/ 20480kbps/ 25600kbps/ 30720kbps/ 35840kbps/ 40960kbps/ 51200kbps/ 61440kbps
[Note:]

・Refer to the catalog specifications for the functions installed in each model.


・If [64 kbps] is selected, set the [Audio transmission mode] on the [Audio] tab to [Off].
9.5 [Audio] for setting sound


・If [Bandwidth control(bit rate)] is set low, the snapshot button may not work depending on the operating environment. If so, select [JPEG] on the live page and run the snapshot with the smallest resolution delivered.


・[MULTI] When playing back images stored on the SD Memory Card, the [Bandwidth control(bit rate)] must be set to [Unlimited] or above [51200 kbps].


[Easy IP Setup accommodate period]
Set the time to enable Network Settings from IP-based Simple Configuration Software to either [20min] or [Unlimited] after the computer starts.
[20 minutes]:The camera setting operation using the IP easy setting software is enabled only for 20 minutes after starting the machine.
[Unlimited]:The camera setting operation in the IP easy setting software is always enabled.
[Note:]

・Camera display with the IP easy setting software is always enabled and the camera screen can be opened.


[FTP access to camera]
Use [Allow] or [Forbid] to set whether or not to allow FTP access to the cameras.
[Permission]:Allow FTP access to the camera.
[Prohibition]:FTP access to the camera is prohibited.
[Important]

・If you allow FTP access to the camera, there is a possibility that authentication information (user names, passwords, etc.) will be leaked when accessing the camera from a PC.


[ONVIF®]
Use [On]/[Off] to set whether to use the ONVIF function.
[Enable]:You can use the ONVIF function.
[Disabled]:The ONVIF function cannot be used.
On the Network Page, press the [Advanced] tab. Refer to the following how to display and operate the Advanced menu.
5.1 How to display
5.2 How to operate
Here, the SMTP (mail), FTP/SFTP, NTP, UPnP, HTTPS, DDNS, SNMP, QoS, SRTP, MQTT, and LLDP functions are set.
Click the link to each item to navigate to each setting page.
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


[E-mail notification]
On/Off is used to specify whether to send mail in the following cases.
When an alarm is activated (e-mail to [Alarm] field)
When notifying the remaining capacity of the SD Memory Card (mail notifying destination: [Diag.] field)
When the free space of the SD Memory Card is insufficient (mail to send message to: [Diag.] field)
SD Memory Card recognition errors (mail notification destination: [Diag.] field)
When writing to SD Memory Card is failed (unique alarm notification destination: [Diag.] field)
[Alarm image attachment]
On/Off sets whether or not to attach images when sending mail by alarm detection.
[Note:]

・[New X Fixed-8MP][New X Fixed-6MP][New X Fixed-5MP][Alarm image attachment] is not available when [Image capture mode] is set to [60fps Mode] or [50fps Mode].


[Image capture size]
Select the resolution of the image to be attached to the alarm mail from the following.
JPEG(1)/ JPEG(2)
[SMTP server address]
Enter the IP address or host name of the SMTP server to send e-mail.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . _ ‑
[SMTP port]
Enter the port number to send mail.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、42、53、67、68、69、80、110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[POP server address]
If you selected [POP before SMTP] in [Type], enter the IP address or hostname of the POP server.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . _ ‑
[Important]

・To enter a hostname for [SMTP server address] [POP server address], you must configure the DNS on the [Network] tab of the network page.
14.1 Networking [Network]


・[MULTI] The port numbers 32768 to 49151 cannot be set.


Authentication-Type
Select the authentication method for sending mail from the list below.
None:Without authentication
POP before SMTP:Prior to sending e-mail, authenticate the POP server that receives the e-mail.
SMTP:Authenticate the SMTP server.
[Note:]

・If you do not know how to authenticate e-mail, contact your network administrator.


Authentication-User Name
Enter the username that you want to access the server.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & : ; ¥
Authentication-Password
Enter the password to access the server.
Number of characters that can be entered:0 to 128 characters
Characters that cannot be entered:Double-byte and single-byte symbols " &
[Sender's E-mail address]
Enter the sender's mail address.
The entered mail address is displayed in the From field of the received mail.
Number of characters that can be entered:3 to 128 characters
Input Characters:Half-pitch alphanumeric and half-pitch symbols @ . _ ‑
[SSL]
When sending [Alarm Notification] or [Diag.] mail notification in SSL-encrypted format, set it to [On]. When set to [On], the authentication method is set to [SMTP]. Configure the [User name] and [Password] for authentication.
[Note:]

・Some SMTP servers may not support SSL.


・The SMTP over SSL method is supported. STARTTLS is not supported.


・If set to [On], you might need to set the SMTP port number to 465. Check with your provider for details.


[Address 1] through [Address 4]
Set the mail address of the notification destination. You can set up to 4 notification destinations.
Number of characters that can be entered:3 to 128 characters
Input Characters:Half-pitch alphanumeric and half-pitch symbols @ . _ ‑
To delete a set e-mail address, press [Delete] for the e-mail address to delete.
[Terminal 1]:Mail is notified when an alarm is generated at terminal 1.
[Terminal 2]:Mail is notified when an alarm is generated at terminal 2.
[Terminal 3]:Mail is notified when an alarm is generated at terminal 3.
[VMD]:Mail is notified when operation is detected.
[SCD]:Notifies by e-mail when undesired detection occurs.
[Command Alarm]:Mail notification is executed when a command alarm is entered.
[Audio detection]:Mail is notified when sound is detected.
[Impact detection]:Mail is notified when impact detection is detected.
[Casing open detection]:Mail is notified when opening detection is detected.
[Diag.]:
-SD Memory Card Remaining capacity notification
-SD Memory Card with insufficient free space
-SD Memory Card recognition error
[Auto track]:Mail is notified when an automatic tracking alarm is generated.
[Note:]

・Message recipient The diagnostic mail notified when the [Diag.] field is checked does not reflect the [E-mail subject] and [E-mail body] settings set below.


[E-mail subject(Alarm)]
Enter the subject of the alarm mail.
Number of characters that can be entered:0 to 50 characters
Use the camera title:The camera title is displayed in the mail subject line.
Cause of alarm:Add an alarm factor to the email subject.
[E-mail subject(Diag.)]
Enter the subject of the diagnosis mail.
Number of characters that can be entered:0 to 50 characters
Use the camera title:The camera title is displayed in the mail subject line.
[E-mail body(Alarm)]
Enter the body of the alarm message.
Number of characters that can be entered:0 to 200 characters
Cause of alarm:The alarm cause %p% is added to the message body. The %p% is sent in place of the cause of the alarm.
For operation detection alarm: "VMD"
For undesired detection alarm: "SCD"
For auto-tracking alarm: "AT"
For intrusion alarm by AI-VMD: "INT"
For residence alarm by AI-VMD: "LOI"
For direction alarm by AI-VMD: "DIR"
For line cross alarm by AI-VMD: CLD
For the terminal alarm: The terminal names set in [Terminal 1], [Terminal 2], and [Terminal 3] of the [Terminal name]. (For example, if the name of terminal 1 is [Terminal 1], "Terminal 1")
For command alarm: "CMD"
In the case of the sound detection alarm (AI sound identification target: gunshot): "Audio detection gunshot"
In the case of the sound detection alarm (AI sound identification target: screaming): "Audio detection yell"
In the case of the sound detection alarm (AI sound identification target: horn): "Audio detection Vehicle Horn"
In the case of the sound detection alarm (AI sound identification target: cracking of glass): "Audio detection Glass break"
In the case of sound detection alarm (AI sound identification target: Others): "Audio detection"
For impact detection alarm: "Impact detection"
For opening detection alarm:
When the detection operation is [Alarm notification when the front cover both opening and closing]:
 If the camera front cover has been opened: "Casing open detection Open"
 If the camera front cover is closed: "Casing open detection Close"
When the detection operation is [Alarm notification continue while the front cover is open]:
 If the camera front cover has been opened: "Casing open detection Open"
[Note:]

・[MULTI] In the case of an operation detection alarm and disturbance detection alarm, information to identify the camera is given by the detected camera.
For the operation detection alarm of camera 1: "VMD(CH1)"
For the operation detection alarm of camera 2: "VMD(CH2)"
For the operation detection alarm of camera 3: "VMD(CH3)"
For the operation detection alarm of camera 4: "VMD(CH4)"
For undesired detection alarm of camera 1: "SCD (CH1)"
For undesired detection alarm of camera 2: "SCD(CH2)"
For the disturbance detection alarm of camera 3: "SCD(CH3)"
For the disturbance detection alarm of camera 4: "SCD(CH4)"


Occurrence time:The occurrence time %t% is added to the message text. The %t% is replaced by the time the alarm occurred (hour: minute: second).
[Note:]

・If the SD Memory Card has no free space, [SD Memory Card is FULL] or [SD Memory Card cannot be recognized] is sent.


・By describing the substitute characters in the message text, the cause type and the time of alarm can be automatically assigned.
Alternate character alarm factor: %p%, occurrence time: %t%
(Example of Use)
When the operation detection alarm is generated at 19:13:24 after setting the following character string in the mail body.
Set mail text: %p%alarm occurred at %t%.
Message text: ["VMD" alarm was generated at 19:13:24].
If the body is blank, the email languages that are sent are determined by the [Menu language] of the [Basic].
Specifying [Japanese] sends e-mail in Japanese or in other languages.


[Terminal 1 (Up to 10 characters)]
Enter the name of Terminal 1 used for alarm factors in the mail body.
Characters that cannot be entered:Single-byte characters " &
[Terminal 2 (Up to 10 characters)]
Enter the name of terminal 2 used for alarm factors in the mail body.
Characters that cannot be entered:Single-byte characters " &
[Terminal 3 (Up to 10 characters)]
Enter the name of terminal 3 used for alarm cause in the mail body.
Characters that cannot be entered:Single-byte characters " &
Mail notification example
Mail format when checkbox for camera title is specified in mail subject and check box for alarm factor/occurrence time is specified in mail body
The alarm time is assigned.
The camera title is used for the e-mail subject.
The name specified by terminal names 1 to 3, which are alarm factors, is given.
FTP (File Transfer Protocol) and SFTP (SSH File Transfer Protocol) are file transfer protocols used to send images to servers.
SFTP can safely send images to the server using an SSH (Secure Shell) encrypted data stream.
The following two transmission functions are available.

・Image sent when alarm is generated


・Transmit images periodically


[Note:]

・The factors displayed differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


[Transmission protocol]
Configure the protocol with the destination server by selecting it from FTP/SFTP.
SFTP:Use SFTP as the protocol for communicating with the server.
FTP:Use FTP as the protocol to communicate with the server.
[Important]

・If FTP is selected in the protocol setting, FTP server authentication information (user name, password) may be leaked on the network when sending images to the FTP server. Use of SFTP is recommended.


Alarm settingFixed
Alarm setting (server 1)
[Alarm image transmission]
Select [On] or [Off] to determine whether or not to transmit images when an alarm is detected.
[On]:Transmits an image to the server when an alarm has occurred.
[Off]:Does not transmit an image to the server when an alarm has occurred.
[Note:]

・[New X Fixed-8MP][New X Fixed-6MP][New X Fixed-5MP][Alarm image transmission] is not available when [Image capture mode] is set to [60fps Mode] or [50fps Mode].


[Directory name]
Enter the directory name where the alarm images are to be saved.
For example, enter [/ALARM] to designate the directory [ALARM] under the root directory of the server.
Number of characters that can be entered:1 to 256 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & ;
[File name]
Enter the file name used for the alarm image to be transmitted to the server. The file name will be as follows.
File name:File name entered + Date and time (year, month, day, minute, second) + Sequence number
Number of characters that can be entered:1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & * / : ; < > ? ¥ ¦
When [On] is selected for [Alarm image FTP transmission], you can select the alarm type from the following.
[Terminal 1]:Transmit the image to the server when an alarm occurs in Terminal 1.
[Terminal 2]:Transmit the image to the server when an alarm occurs in Terminal 2.
[Terminal 3]:Transmit the image to the server when an alarm occurs in Terminal 3.
[VMD]:Transmit the image to the server when motion is detected.
[SCD]:Transmit the image to the server when SCD (scene change detection) occurs.
[Auto track]:Transmit the image to the server when an auto track occurs.
[Audio detection]:Transmit the image to the server when audio detection occurs.
[Impact detection]:Transmit the image to the server when impact detection occurs.
[Casing open detection]:Transmit the image to the server when opening detection occurs.
[Command alarm]:Transmit the image to the server when a command alarm is entered.
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


[FTP transmission retry]
Select [On] or [Off] to determine whether or not to resend failed FTP transmissions.
[On]:If transmission fails, transmissions are resent until they are successfully sent.
[Off]:If transmission fails, the image that failed to be sent is discarded and the next image is sent.
[Note:]

・When SFTP is selected in [Transmission protocol] settings, FTP transmission retry is unavailable.


・When 2fps or 3fps is selected in [Refresh interval], FTP transmission retry is unavailable.  


[Pre alarm]
[Transmission interval]
Select the transmission interval of images before an alarm occurs from the following.
When 60fps mode, 30fps mode or 15fps mode is selected for [Image capture mode]:

0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps/ 2fps/ 3fps


When 50fps mode, 25fps mode or 12.5fps mode is selected for [Image capture mode]:

0.08fps/ 0.17fps/ 0.28fps/ 0.42fps/ 1fps/ 2.1fps/ 3.1fps


[Maximum number of images]
Select the number of images to be transmitted from the following.
[0 pic]/[1 pic]/[2 pics]/[3 pics]/[4 pics]/[5 pics]/[6 *]/[7 *]/[8 *]/[9 *]/[10 *]/[20 *]/[30 *]/[40 *]/[50 *]

[Recording duration]
Approximate time to be taken to save the set [Maximum number of images] with the set [Transmission interval] will be displayed.
[Note:]

・When [JPEG(1)] is selected for the capture size of the image to be transmitted, pre alarm is unavailable if the image capture size of [JPEG(1)] is larger than [1920x1080].


・When “On” is selected for [Image compression rate upon alarm detection], only post alarm recordedimages are compressed. Compression is not applied to pre alarm recorded images.


・When a selection with an asterisk (*) on the right of it is selected for [Maximum number of images] of [Pre alarm], the specified number of images may not be able to be sent depending on the image capturesize and image quality. The following table shows the maximum number of images that can be sentfor pre alarm.


・If the refresh interval is higher than 1fps, the maximum number of pre-alarm images is 10.


Image quality
0
1
2
3
4
5
6
7
8
9
Image capture size
1920x1080
9
9
9
9
10
10
10
20
30
40
1280x960
5
6
7
8
10
10
10
20
30
40
1280x720
7
8
10
10
10
20
20
30
40
50
VGA
10
20
20
30
30
40
50
50
40
50
640x360
20
30
40
50
50
50
50
50
50
50
QVGA
40
50
50
50
50
50
50
50
50
50
320x180
50
50
50
50
50
50
50
50
50
50
[Post alarm]
[Transmission interval]
Select the transmission interval for the alarm image transmission from the following.
When 60fps mode, 30fps mode or 15fps mode is selected for [Image capture mode]:

0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps/ 2fps/ 3fps


When 50fps mode, 25fps mode or 12.5fps mode is selected for [Image capture mode]:

0.08fps/ 0.17fps/ 0.28fps/ 0.42fps/ 1fps/ 2fps/ 3fps


[Number of images]
Select the number of images to be transmitted from the following.
[1 pic]/[2 pics]/[3 pics]/[4 pics]/[5 pics]/[6 pics]/[7 pics]/[8 pics]/[9 pics]/[10 pics]/[20 pics]/[30 pics]/[50 pics]/[100 pics]/[200 pics]/[300 pics]/[500 pics]/[1000 pics]/[1500 pics]/[2000 pics]/[3000 pics]
[Recording duration]
Approximate time to be taken to save the set [Number of images] with the set [Transmission interval] willbe displayed.
[Note:]

・If the resolution of the image to be transmitted is set to JPEG(1), and the JPEG(1) resolution is larger than [1920×1080], the maximum refresh interval will be 1fps.


・If the refresh interval is higher than 1fps, the maximum number of pre-alarm images is 10.


[Image capture size]
Select the image capture size of images transmitted when an alarm occurs from the following.
JPEG(1)/JPEG(2)
Alarm setting (server 2)
[Alarm image transmission]
Select [On] or [Off] to determine whether or not to transmit images when an alarm is detected.
[On]:Transmits an image to the server when an alarm has occurred.
[Off]:Does not transmit an image to the server when an alarm has occurred. 
[Note:]

・[New X Fixed-8MP][New X Fixed-6MP][New X Fixed-5MP][Alarm image transmission] is not available when [Image capture mode] is set to [60fps Mode] or [50fps Mode].


[Directory name]
Enter the directory name where the alarm images are to be saved.
For example, enter [/ALARM] to designate the directory [ALARM] under the root directory of the server.
Number of characters that can be entered:1 to 256 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & ;
[File name]
Enter the file name used for the alarm image to be transmitted to the server. The file name will be as follows.
File name:File name entered + Date and time (year, month, day, minute, second) + Sequence number
Number of characters that can be entered:1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & * / : ; < > ? ¥ ¦
When [On] is selected for [Alarm image FTP transmission], you can select the alarm type from the following.
[Terminal 1]:Transmit the image to the server when an alarm occurs in Terminal 1.
[Terminal 2]:Transmit the image to the server when an alarm occurs in Terminal 2.
[Terminal 3]:Transmit the image to the server when an alarm occurs in Terminal 3.
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


・Terminals 1 to 3 of [Alarm setting (Server 2)] can be selected only when terminals 1 to 3 of [Alarm setting/Alarm setting (Server 1)] are not selected.


・[Alarm setting (Server 2)] uses [FTP transmission retry], [Pre alarm], [Post alarm], and [Image capture size] of [Alarm setting/Alarm setting (Server 1)].


Periodic transmission settings
Periodic image transmission is available only for “Alarm setting/Alarm setting (Server 1)”.
[Periodic image transmission]
Select [On] or [Off] to determine whether or not to transmit images using the periodic image transmission function.
[On]:Periodic image transmission is performed.
[Off]:Images are not sent regularly.
[Note:]

・[New X Fixed-8MP][New X Fixed-6MP][New X Fixed-5MP][Periodic image transmission] is not available when [Image capture mode] is set to [60fps Mode] or [50fps Mode].


[Important]

・When using periodic image transmission, it is necessary to configure the schedule settings of FTP/SFTP periodic image transmission on the [Schedule] tab of the “Schedule” page.
7.3.9 Schedule: Setting FTP/SFTP Periodic Transmission (FTP/SFTP Periodic Transmission Setting Screen)


[Directory name]
Enter the name of the directory where you want to save the image file to be sent.
For example, if you want to specify the img directory under the root directory of the server, enter [/img].
Number of characters that can be entered:1 to 256 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & ;

[File name]
Enter the image file name to be sent and select the file name format from the following.
File name + Date and time:[File name + Transmission date and time (year, month, day, minute, second) + 00] is used as the file name.
File name is fixed:Use the entered file name as it is. When set to [Fix], the transmitted files are always overwritten.
Number of characters that can be entered:1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & ; : / * < > ? ¥ ¦
[Note:]

・When [Name w/time&date] is selected, the file name will be [[Entered file name] + [Time and date (year/ month/ day/ hour/ minute/ second)] + [Serial number (starting from 00)]] + [s] during summer time.


・If [Alarm setting 1] and [Periodic transmission settings] are set at the same time when an alarm occurs, [Alarm setting 1] will be performed when an alarm occurs.


・If [Alarm setting 2] and [Periodic transmission settings] are set at the same time when an alarm occurs, both [Alarm setting 2] and [Periodic transmission settings] will be performed when an alarm occurs.


[Transmission interval]
Select the interval for the periodic image transmission from the following.
[1s]/ [2s]/ [3s]/ [4s]/ [5s]/ [6s]/ [10s]/ [15s]/ [20s]/ [30s]/ [1min]/ [2min]/ [3min]/ [4min]/ [5min]/ [6min]/ [10min]/ [15min]/ [20min]/ [30min]/ [1h]/ [1.5h]/ [2h]/ [3h]/ [4h]/ [6h]/ [12h]/ [24h]
[Image capture size]
Select the image capture size of images to be transmitted from the following.
JPEG(1)/JPEG(2)
SFTP server 1 settings
SFTP server 2 settings 
[Note:]

・If [Transmission protocol] is set to FTP, you cannot configure the SFTP server.


[SFTP server address]
Enter the IP address or host name of the SFTP server that sends the image.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols: . _ ‑
[Important]

・If you want to enter a hostname for [SFTP server address], you must configure the DNS on the [Network] tab of the network page.
14.1 Networking [Network]


[Port number]
Enter the control port number of the SFTP server.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80、110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Host key hash]
Enter the hash value for the public key of the SFTP server.
Number of characters that can be entered:43 to 44 characters
Input Characters:Half-pitch alphanumeric and half-pitch symbols + / =
[User name]
Enter the user name (login name) to access the SFTP server.
Number of characters that can be entered:1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & : ; ¥
[Password]
Enter the password to access the SFTP server.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " &
FTP server 1 setting
FTP server 2 settings
[Note:]

・If [Transmission protocol] is set to SFTP, you cannot configure the FTP server.


[FTP server address]
Enter the IP address or host name of the FTP server that sends the image.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . _ -
[Important]

・If you want to enter a hostname for [FTP server address], you must configure the DNS on the [Network] tab of the network page.
14.1 Networking [Network]


[User name]
Enter the user name (login name) to access the FTP server.
Number of characters that can be entered:1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & : ; ¥
[Password]
Enter the password to access the FTP server.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " &
[Control port]
Enter the control port number of the FTP server.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80 110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Recording priority]
Select FTP communication mode from Passive mode/Active mode.
Normally, select [Passive]. If you cannot connect with [Passive], switch to [Active].
[Passive]:Sets FTP communication mode to passive mode.
[Active]:Set FTP communication mode to active mode.
This section configures the NTP server, including the address and port number of the NTP server.
[Important]

・If you need to set the time more accurately in system operation, use the NTP server.


[Time adjustment]
Select the time adjustment method from the following. The time adjusted in the selected manner is used as the standard time of the machine.
[Manual]:The time set in the [Basic] tab on the base page is used as the standard time of the computer.
[Synchronize to NTP Server]:The time automatically adjusted in synchronization with the NTP server is used as the standard time of the machine.
[NTP server address setting]
If you selected [Synchronization with NTP server] in [Time adjustment], select how to get the NTP server address.
[Auto]:Get the NTP server address from the DHCP server.
[Manual]:Enter the NTP server address into the [NTP server address] to configure the NTP server address.
[Important]

・To obtain [NTP server address] from a DHCP server, you must set [Network Settings] to DHCP, AutoIP, or Omakase on the [Network] tab of the network page.
14.1 Networking [Network]


[NTP server address]
If you selected [Manual] in [NTP server address setting], enter the IP address or hostname of the NTP server.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . _ -
[Important]

・To enter a hostname for [NTP server address], you must configure the DNS on the [Network] tab of the network page.
14.1 Networking [Network]


[NTP port]
Enter the port number of the NTP server.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80 110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Time adjustment interval]
Select the interval (in 1-24 hour increments) at which the time is to be acquired from the NTP server.
[NTP test]
Select [Synchronization with NTP server] for [Time adjustment], set up the NTP server, and then press [Execute]. You can communicate with the NTP server, perform time synchronization, and check the NTP operation.
[Note:]

・When the NTP test is successful, the [The NTP time correction completed successfully.] is displayed.


・If the NTP test fails, the [The NTP time correction failed.] is displayed.


・If [Time adjustment] is set to [Manual], the [Execute] buttons for NTP tests will be grayed out.


・If [Time adjustment] is set to [Synchronization with NTP server] and the NTP server address is not set, the [Execute] buttons for the NTP tests are grayed out.


[Note:]

・[MULTI_PTZ] When UPnP is set to ON and access via the Internet is set to [Multi-directional + PTZ] by [Live view], only the image of the accessed camera is displayed.


This machine supports UPnP (Universal Plug and Play). The UPnP function enables you to set the following settings automatically.
-configure the port forwarding function for routers. However, a UPnP-enabled router is required. This setting is useful for accessing the camera from the Internet or from a mobile or tablet terminal.
-Create a shortcut to the camera in the [Network] folder of the PC and update the shortcut automatically even if the camera has changed IP addresses.
[Auto port forwarding]
Configure on/off whether to use the router's port forwarding function.
To use the Automatic Port Forwarding feature, the router you use must be UPnP-enabled and UPnP enabled.
[Note:]

・Automatic port forwarding may change the port number. If this is changed, the port number of the camera registered on the PC or recorder must be changed.


・The UPnP feature can be used to connect a camera to an IPv4 network. IPv6 is not supported.


・To verify that auto-port forwarding has been configured correctly, click on the [Status] tab on the Maintenance page and make sure that the [UPnP] status is [On].
16.3 [Status] for checking the status
If [On] is not displayed, please read [Cannot access cameras from internet] in "Trouble!?"
18.2 Trouble!?


・If the live screen or configuration screen is not displayed correctly, such as when replacing the routers to be used, set [UPnP(Auto port forwarding)] to [Off] once and then set it to [On] again.


[Camera short cut]
Use the [On] and [Off] buttons to specify whether to make shortcuts to the cameras in the [Network] folder of your computer.
Select [On] to shortcut the cameras.
To use the camera shortcut function, enable the UPnP function on the PC beforehand.
[Note:]

・You must add a Windows component to view shortcuts to the cameras in the Windows [Network] folder. Enable UPnP by referring to the following.
Start > [Set] > Network and Internet > Ethernet > Network and Sharing Center > Enable Network Discovery in Change Shared Advanced Settings > Click Save Change.


By using the HTTPS function, you can encrypt the access to the camera and increase the security of communication.
For details on how to configure HTTPS, see below.
14.3 Setting up HTTPS
[Note:]

・[MULTI_PTZ] When the HTTPS connection is accessed, only the camera accessed is protected.


[HTTPSConnection]
Set the connection method to the machine.
HTTP & HTTPS:HTTP and HTTPS connections are enabled.
HTTPS:Only the HTTPS connection is enabled.

Select the TLS to be used when HTTPS is selected.
TLS1.1、TLS1.2:Enable/disable.
TLS1.3:It is always valid and cannot be set to invalid.
[Note:]

・To connect to HTTPS when HTTP is selected, first configure the HTTPS connection. The HTTPS connection is enabled even if the setting is changed to HTTP.


・When accessing the camera with HTTPS, the display speed of the screen and the frame rate of the movie may decrease.


・When accessing the camera with HTTPS, it may take a long time before the image is displayed.


・When you access the camera with HTTPS, the image may be distorted or the sound may be interrupted.


・If you set the connectivity to [HTTPS], the maximum delivery is limited to 32Mbps.


・It is recommended that TLS 1.1 be disabled for security reasons.


・When TLS1.1 is enabled, TLS1.2 is also enabled.


・When TLS1.2 is disabled, TLS1.1 is also disabled.


・When you change the TLS1.2 setting, you need to reboot the camera. After rebooting, you cannot perform operations for around 2 minutes, just as when the camera is turned on.


[HTTPS-Select Certificate]
Select the certificate to use in HTTPS.
[Pre-install]:Select the pre-installation certificate.
CA:Select a CA certificate. This is displayed only if the CA certificate is installed.
[HTTPS-HTTPS port]
Set the port number to use for HTTPS.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80 110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Pre-installation Certificate-Root Certificate Acquisition]
Clicking [Execute] downloads the route certificate for the pre-installation certificate. By installing the root certificate on your PC, you can verify the signature of the pre-installation certificate.
[CA certificate-CRT key generate]
Creates a CRT key (SSL encryption key) for use in an HTTPS connection using a CA certificate.
CRT key generation is performed in [CRT key generation dialog] displayed when [Execute] is clicked.
[CA Certificate-Generate Certificate Signing Request]
This generates a signature request (CSR Certificate Signing Request) to apply to a Certificate Authority when using a security certificate issued by a CA (Certificate Authority) as a security certificate to be used in HTTPS.
Create a signature request (CSR) by clicking on the [Execute] button. This is displayed in the [Create Signature Request (CSR) dialog].
[CA certificate-CA certificate install]
Install the CA certificate (security certificate) issued by the certification authority and display information about the installed CA certificate (security certificate).
When [Select File] is clicked, the [Open Dialog] is displayed. Select the CA certificate (security certificate) file issued by the authentication authority. Click [Execute] to install the CA certificate (security certificate).
If a CA certificate (security certificate) is installed, the file name of the installed CA certificate (security certificate) is displayed.
[CA certificate-information]
The information of the CA certificate (security certificate) is displayed.
When [Execute] is clicked, the registered contents of the installed CA certificate (security certificate) are displayed in the [CA Certificate Confirmation Dialog]. If a CA certificate (security certificate) is not installed, the content of the generated signature request (CSR) is displayed.
Clicking [Delete] deletes the installed CA certificate (security certificate).
[Important]

・When deleting a valid CA certificate (security certificate), make sure that you have a backup of the CA certificate (security certificate) on your PC or recording media. To reinstall, a CA certificate (security certificate) is required.


[Note:]

・If the connection method setting is changed, the connection must be accessed again after a while using [http://Camera IP address] or [https://Camera IP address].


・When accessing the camera with HTTPS, the display speed of the screen and the frame rate of the movie may decrease.


・When accessing the camera with HTTPS, it may take a long time before the image is displayed.


・When you access the camera with HTTPS, the image may be distorted or the sound may be interrupted.


・If you set the connectivity to [HTTPS], the maximum delivery is limited to 32Mbps.


To access the computer via the Internet, you must configure the DDNS function.
See below for instructions on how to configure DDNS.
14.4 How to configure DDNS
[Area]
Select the region where the camera is installed.
[Japan]/[Global]
[Note:]

・Select [Japan] when using cameras in Japan. The [Viewnetcam.com] services displayed when [Global] is selected are not accessible from within Japan.


・[Indoor PTZ] [Viewnetcam.com] servicedoes not appear even if you select [Global].


[Service]
Select whether or not to use the DDNS service to be used.
[Off]:Do not use DDNS.
[Viewed Net]:Use [Viewnetcam.com] services.
[Dynamic DNS Update]:[DHCP-NON]Dynamic DNS Update (RFC 2136 compliant) is used without DHCP linkage.
[Dynamic DNS Update]:[DHCP]Dynamic DNS Update (RFC 2136 compliant) is used for DHCP linkage.
[Note:]

・If you use DNS Update [Dynamic DNS Update (RFC2136)], contact your network administrator to select DHCP or DHCP linkage.


Here, the setting for the SNMP function is performed. Connecting using the SNMP Manager enables you to check the status of your computer. Contact your network administrator if you want to use the SNMP feature.
SNMP setting
[SNMP setting]
Set whether to Enable/Disable the SNMP function.
[Note:]

・If [SNMP setting] is set to [Disable], [SNMP agent setting] and [SNMP trap setting] cannot be set.


SNMP agent setting
[SNMP version]
Select the SNMP version to be used.
[SNMPv1/v2]:SNMPv1/v2 is enabled.
[SNMPv3]:SNMPv3 is enabled.
[SNMPv1/v2/v3]:SNMPv1/v2/v3 is enabled.
SNMPv1/v2 − [Community]
Enter the community name to be monitored.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte
Initial setting:Blank space
[Important]

• When using the SNMP feature on SNMPv1/v2, be sure to enter a community name. If the community name is blank, you cannot use the SNMP feature. Do not set a community name that can be easily guessed. (e.g., public)


SNMPv1/v2 − [Manager address]
When the SNMP version is v1 and v2, enter the IP address of the SNMP manager that allows requests. If blank, allow requests from all IP addresses.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . /
[Note:]
You can restrict the IP address of the SNMP manager to allow requests per subnet by entering the IP address/Mask length of the subnet.
For example, if you enter [192.168.0.1/24], SNMP manager requests from [192.168.0.1] to [192.168.0.254] are allowed.
[SNMPv3] − [User name (1 to 32 characters)]
Set the SNMPv3 username.
Number of characters that can be entered:Blank or 1 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & : ; ¥
[SNMPv3][Authentication]
Displays the SNMPv3 authentication method.
[Note:]

・If you upgrade while [MD5] is set in [Authentication], the [Authentication] operates using [MD5]. Click the [Set] button to change [Authentication] to [SHA1].


[SNMPv3] − [Encryption method]
Select the SNMPv3 encryption method from DES/AES.
[SNMPv3] − [Password]
Set the SNMPv3 password.
Number of characters that can be entered:blank or 8-20 characters
Characters that cannot be entered:Double-byte and single-byte symbols " &
SNMPv2-MIB systemFixed

[System name]
Enter the device name to manage the machine using the SNMP function.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte
[Location]
Enter the location where the machine was installed.
Number of characters that can be entered:0 to 32 characters
[Contact]
Enter the administrator's mail address or phone number.
Number of characters that can be entered:0 to 255 characters
Characters that cannot be entered:Double-byte
[SNMP trap settings]
Sets ON/OFF of SNMP trap notification.
[Destination of Trap] − [Address]
SNMP Enter the destination address for the trap notification.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : .
[Important]

・IPv6 address and hostname cannot be used as the notification destination.


[SNMPv2c] − [Community]
Enter the community name of the SNMP trap notification destination.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte
Trap notificationFixed
[SNMP Generic trap] − [coldStart] − [Enable/Disable]
If the check box is checked, the trap (SNMPv2-MIB::coldStart) is notified when the camera starts.
[SNMP Generic trap] − [coldStart] − [Trap string]
If you want to extend the trap when the computer starts, you can set the character string.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol !  "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[SNMP Generic trap] − [linkUp] − [Enable/Disable]
When the checkbox is checked, the trap (SNMPv2-MIB::linkup) is notified when the machine is linked up.
[SNMP Generic trap] −[LinkUp]− [Trap string]
To extend the trap when the computer is linked up and notify, set the character string.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[SNMP Generic trap] − [authenticationFailure] − [Enable/Disable]
If the check box is checked, a trap (SNMPv2-MIB: authentication failure) is notified when an SNMP authentication error occurs.
[SNMP Generic trap] − [authenticationFailure] − [Trap string]
If you want to extend the trap when an SNMP authentication error occurs, you can set the string.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol  ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm]-[Terminal 1]-[Enable/Disable]
When the check box is checked, the trap is notified when an alarm is generated at terminal 1.
[Alarm]-[Terminal 1]-[Trap string]
Set the character string to be used for notifying [Terminal 1] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm]-[terminal 2]-[Enable/Disable]
When the
check box is checked, the trap is notified when an alarm is generated at terminal 2.
[Alarm]-Terminal 2-[Trap string]
Set the character string to be used for notifying [Terminal 2] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm]-Terminal 3-[Enable/Disable]
When the check box is checked, the trap is notified when an alarm is generated at terminal 3.
[Alarm]-Terminal 3-[Trap string]
Set the character string to be used for notifying [Terminal 3] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [VMD] − [Enable/Disable]
When the check box is checked, the trap is notified when the operation is detected.
[Alarm] − [VMD] − [Trap string]
Specify the strings to be used to notify [VMD] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0 to 9 (half-pitch), A to Z (half-pitch, uppercase, lowercase), half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [Auto track] − [Enable/Disable]
When the check box is checked, the trap is notified when automatic tracking occurs.
[Alarm] − [Auto track] − [Trap string]
Specify the strings to be used to notify [Auto track] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [Audio detection] − [Enable/Disable]
When the check box is checked, the trap is notified when sound detection occurs.
[Alarm] − [Audio detection] − [Trap string]
Specify the strings to be used to notify [Audio detection] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [Command alarm] − [Enable/Disable]
When the check box is checked, the trap is notified when a command alarm occurs.
[Alarm] − [Command alarm] − [Trap string]
Specify the strings to be used to notify [Command alarm] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [Impact detection] − [Enable/Disable]
When the check box is checked, the trap is notified when impact detection occurs.
[Alarm] − [Impact detection] − [Trap string]
Specify the strings to be used to notify [Impact detection] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Alarm] − [Casing open detection] − [Enable/Disable]
When the check box is checked, the trap is notified when opening detection occurs.
[Alarm] − [Casing open detection] − [Trap string]
Specify the strings to be used to notify [Casing open detection] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
SD Memory Card-[Diag.]-[Enable/Disable]
When the check box is checked, the trap is notified in the following cases.
When notifying the remaining capacity of the SD Memory Card
-when the free space on the SD memory card is insufficient
-SD Memory Card recognition error

SD Memory Card-[Diag.]-[Trap string]
Specify the strings to be used to notify [Diag.] traps.
Number of characters that can be entered:0 to 32 characters
Input Characters:0-9 (half-pitch), A-Z (half-pitch, uppercase, lowercase) and half-pitch symbol ! "  #  $  %  &  '  (  )  *  +  ,  ‑  .  /  :  ;  =  ?
[Note:]

・The items that can be set differ depending on the function of the model.


・Refer to the catalog specifications for the functions installed in each model.


・[PTZ] [Auto track] can be set only for PTZ-cameras.


This section configures the settings for the Diffserv function and the shaping of streams.
Diffserv
The Diffserv feature sets the priority of image/voice data forwarded from the router and other commands.
The priority you set on your computer must be matched to the DSCP value set on the router.
Contact your network administrator if you want to use the Diffserv function.
[Image DSCP(0-63)]
Enter the packet priority order for the video data.
Configurable values:0~63
[Audio DSCP(0-63)]
Enter the packet priority order for audio distribution.
Configurable values:0~63
TCP alarm notification DSCP (0-63)
Enter the packet priority order for the unique alarm notification.
Configurable values:0~63
Shaping of streams
[Shaping of stream]
Use the [On] [Off] to control whether H.265 (or H264) images are not bursted.
It may be effective when network devices divert image data from the camera, etc., but the displayed image may be delayed.
[Off]:Disables the shaping function of the stream.
[On]:Enables the shaping function of the stream.
[Note:]

・If you are concerned about the delay of the image to be displayed, set it to Off.


Here, the settings for the SRTP function are performed.
[SRTP]
Use [On] or [Off] to set whether to use the SRTP function.
[On]:Use the SRTP function.
[Off]:The SRTP function is not used.
[Note:]

・You can also deliver RTP if SRTP is set to [On].


・For client information that can be connected to the camera using the SRTP function, please refer to our technical information website<Control No. C0318>.


This section configures the MQTT (Message Queuing Telemetry Transport) function. When an alarm is generated, the MQTT server can be notified of an event caused by the alarm.
[MQTT settings]
Use [On]/[Off] to specify whether the MQTT function is enabled or not.
Connect to the configured server if it is set to [On] or [On] when the cameras are started.
When the set alarm occurs, the setting is notified to the server.
[On]:Use the MQTT function.
[Off]:MQTT function is not used.
Server
[Address]
Enter the IP address or host name of the MQTT server to be notified when an alarm is generated.
Number of characters that can be entered:1 to 128 characters
Input Characters:One-byte alphanumeric and one-byte symbols : . _ -
[Port number]
Enter the MQTT server port number.
Configurable port number:1~65535
The following port numbers cannot be set because they are used by this computer.
20、21、22、23、25、42、53、67、68、69、80 110、123、161、162、443、554、995、1883、8883、10669、10670、59000~61000
[Note:]

・[MULTI] The port numbers 32768 to 49151 cannot be set.


[Protocol]
Select the protocol to be used for connection with the MQTT server from MQTT over SSL/MQTT over TCP.
MQTT over SSL:Encrypt communication with the MQTT server with SSL.
MQTT over TCP:Do not encrypt communication with the MQTT server.
[User name]
Enter the user name to access the MQTT server.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " & : ; ¥
[Password]
Enter the password to access the MQTT server.
Number of characters that can be entered:0 to 32 characters
Characters that cannot be entered:Double-byte and single-byte symbols " &
Root CA certificationBook
[Installation]
Install the root CA certificate issued by the certification authority.
When [Select File] is clicked, the [Open File Dialog] is displayed. Select the root CA certificate file issued by the authentication authority. Click [Execute] to install the root CA certificate.
The data format of the root CA certificate can be PEM or DER.
[Information]
The root CA certificate information is displayed.
[Off]:Root CA certificate is not installed.
Root CA Certificate Host Name:Displayed when installed.
You can view the root CA certificate in detail by clicking [Execute].
Clicking [Delete] deletes the installed root CA certificate.
[Server certificate verification]
Select [MQTT over SSL] for [Protocol] and, if [Server certificate verification] is [On], verify the server certificate using the root CA certificate registered when connecting to SSL.
[Note:]
If the [Server certificate verification] is [On], install the root CA certificate.
Provision of noticeFixed
[Alarm]
Check the alarm event to notify the MQTT server.
[Terminal 1]:The MQTT server is notified when an alarm is generated at terminal 1.
[Terminal 2]:The MQTT server is notified when an alarm is generated at terminal 2.
[Terminal 3]The MQTT server is notified when an alarm is generated at terminal 3.
[VMD]:The MQTT server is notified when an operation detection occurs.
[Audio detection]:Notifies the MQTT server when sound detection occurs.
[Command alarm]:Notifies the MQTT server when a command alarm is entered.
[Impact detection]:Notifies the MQTT server when impact detection occurs.
[Casing open detection]:Notifies the MQTT server when opening detection occurs.
[Topic]
Specify the name of the MQTT topic to be sent. The topics are hierarchically separated by /.
Number of characters that can be entered:1 to 128 characters
Input Characters:Single-byte alphanumeric and single-byte symbols
Prohibited Characters:One-byte symbol \
[Payload]
Set the MQTT message payload.
Number of characters that can be entered:1 to 128 characters
Input Characters:Single-byte alphanumeric and single-byte symbols
Prohibited Characters:One-byte symbol \
[QoS]
Select the level of QoS from 0, 1, or 2. 0<1<Communication quality is high with 2.
0:QoS0 delivers up to one message. Messages are not guaranteed to reach the server.
1:In QoS1, messages are delivered at least once. Messages are guaranteed to reach the destination, but may be duplicated.
2:QoS2 delivers the message exactly once. Messages are guaranteed to arrive only once without excess or deficiency.
[Retain]
Check this box to have the last notified message saved on the MQTT server.
This section configures the LLDP (Link Layer Discovery Protocol) function. Interoperation can be realized by transmitting and receiving the device information of the camera with LLDP-compatible devices.
[LLDP]
You can configure [On] and [Off] to enable the LLDP function and Fabric Attach.
[Enable]:Use the LLDP function.
[Disabled]:The LLDP function is not used.
When set to [On], LLDP is sent with TLVs checked in the following tables.
For the model supporting *PoE+ power supply, LLDP including TLV with checks in the following table is sent for PoE+ power supply even if set to [Off].
Fabric Attach authentication key
Enter the key to be used for Fabric Attach authentication. It is valid only when [LLDP] is [On].
Number of characters that can be entered:0 to 32 characters (blank if not Fabric Attach authentication)
Input Characters:One-byte alphanumeric characters
[Note:]

・Press [Set] to restart the computer. After restarting, the product cannot be operated for about two minutes as it was when the power was turned on.


・Information on devices that can be connected via Fabric Attach can be found on our technical information website.


Here, you set up HTTPS to encrypt camera access and enhance communication security.
HTTPS can be configured using pre-installed certificates on the camera body or using CA (CA) certificates obtained between the customer and the certification authority.
HTTPS setting method (pre-installation) is shown on the support video page of the support site.<Control No. P0002>. Please refer to configure HTTPS (CA certificate)<Control No. P0003>.
[Note:]

・[MULTI_PTZ] When the HTTPS connection is accessed, only the camera accessed is protected.


・[Subject Alternative Name] can be set in [Signature Request (CSR) Generation Dialog] in the software Ver.2.50. For details, please read the following.


14.3.1 How to generate a signing request (CSR)
1
Click the [Execute] button in [CA Certificate - Generate Certificate Signing Request].
→ The “CA Certificate - Generate Certificate Signing Request” screen is displayed.
2
Enter the information for the certificate to be generated.
Item
Explanation
Available number of characters
[Host name]
Enter the camera address or the host name.
64 characters
[Subject Alternative Name]
Enter the domain name.
64 characters per domain
Available number of domain registration: 8
[Country]
Enter the country code.
2 characters: Country code
[State]
Enter the name of the state.
128 characters
[Locality]
Enter the name of the locality.
128 characters
[Organization]
Enter the name of the organization.
64 characters
[Organizational Unit]
Enter the name of the organizational unit.
64 characters
[CRT key]
Displays the key size of the current CRT key and the date/time it was generated.
-
[Note:]

・When using a CA certificate, make sure you enter the information that is required by the certification authority you are applying to.


・For the [Host name], [State], [Locality], [Organization], and [Organizational Unit], you can enter the following characters:
0 to 9, A to Z, a to z, and the following symbols:
- . _ , + / ( )


・For the [Subject Alternative Name], you can enter the following characters:
0 to 9, A to Z, a to z, and the following symbols:
. : * , -


・When entering multiple domain names in [Subject Alternative Name], separate them with commas.


When using the DDNS function on your computer, you can use one of the following DDNS services:
[Viewnetcam.com] services
Dynamic DNS Update (RFC 2136)
[Important]

・You must configure port forwarding for routers before using the DDNS service.


・About [Dynamic DNS (DDNS)] Update (RFC 2136)
We do not guarantee the operation of any DDNS services other than the [Viewnetcam.com] service. Therefore, you are not liable for any failure or damage caused by the use of DDNS services other than the [Viewnetcam.com] service.
For selection and configuration of DDNS services other than [Viewnetcam.com] services, please contact the service provider.


・Check the [Viewnetcam.com] service website for browsers supported by the [Viewnetcam.com] service.


[Note:]

・The [Viewnetcam.com] service (fee-based) is the DDNS service we recommend. For more information about the [Viewnetcam.com] service, refer to the [Viewnetcam.com] Service website (http://www.viewnetcam.com/).


About DDNS Services (IPv4/IPv6)
You can view camera images via the Internet by using the DDNS service.
The DDNS service is a service that matches a domain name with a dynamically changing global address. You can configure the [Viewnetcam.com] service (charged for IPv6, but both IPv4 and IPv6 connections are required) or dynamic DNS Update (RFC2136 compliant) for DDNS services.
Since many providers provide services that change their global addresses rather than being fixed, the camera may not be able to access the previous global addresses after a period of time. To access cameras with non-fixed global addresses from the Internet, you must have one of the following services:
DDNS services (e.g., [Viewnetcam.com] services)
This service can be accessed with a fixed registered domain name (e.g., *****.miemasu.net) even if the global address changes. You must also subscribe to domain name services when using IPv6 connections.
For more information about [Viewnetcam.com] Services, see the [Viewnetcam.com] website.
Fixed IP address service (e.g. service of subscription provider)
This service does not change the global address (fixed).
DDNS Service Mechanism (for [Viewnetcam.com] Service)
The contracted provider assigns a global address to the router (or camera). The global address assigned at this time is not a fixed but a changing address.
If you subscribe to [Viewnetcam.com] services, the cameras are assigned a unique [Domain Name] (e.g., *****.miemasu.net). The camera manages the camera's domain name and the global address of the router (or camera) by automatically notifying the [Viewnetcam.com] service server of the router's (or camera's) global address (the [Viewnetcam.com] service server).
The [Viewnetcam.com] service server registers the global addresses and domain names of routers (or cameras) with the DNS server.
When accessing a camera via the Internet, the DNS server determines the global address of the registered router (or camera) by entering the URL containing the domain name into the Web browser.
You can access routers (or cameras) with an indexed global address to monitor the image.
[Note:]

・Contact your provider to determine whether your IP address is fixed.


・Depending on the provider, local addresses may be assigned. In that case, the DDNS service is not available. Please contact the provider you subscribe to.


1
On the [Advanced] tab of the Network Page, select [DDNS], and then select [Japan] from the [Area] tab.
4
Select [Viewnetcam.com] and press [Set].
5
Clicking on the URLs displayed on the [Link to MIEMASUNET registration] opens a new window for registering [Viewnetcam.com] Services.
6
Register [Viewnetcam.com] Services according to the window. If the [Viewnetcam.com] services registration window is not displayed, check that the PC is connected to the Internet and press the Update browser button.
7
Re-display the cameras and ensure that the [Personal(Camera) URL] shows the domains (xxxx.miemasu.net:xxx) registered with the [Viewnetcam.com] services.
[Note:]

・The URLs of the registered cameras are displayed on the [Personal(Camera) URL] when registration to the [Viewnetcam.com] services has been completed. This address is used when accessing the camera via the Internet. It is recommended that you register this URL as your favorite browser function. The camera's URLs can also be viewed in the [Status] [Personal(Camera) URL] on the Camera Maintenance page.


・The URLs of the cameras can be used after they are registered with the [Viewnetcam.com] services. (It may take up to 30 minutes for the URL of the registered camera to become valid.)
However, depending on the router, this URL cannot be accessed from a PC connected to the same network (LAN) as the camera.


・If [Link to MIEMASUNET registration] is not displayed, make sure that you have registered to [Viewnetcam.com] and that your PC is connected to the Internet, and then press the Update browser button.


・If [User registered] is displayed in the [Viewnetcam.com] [Status] on the [Status] tab of the Maintenance page, restart the camera after registering the [Viewnetcam.com] service.
After restarting, make sure that the URLs registered in the [Viewnetcam.com] [Personal(Camera) URL] are displayed in the [Status] tab on the Maintenance page.


・The [Viewnetcam.com] service provides services other than dynamic DNS services. For more information, refer to the [Viewnetcam.com] services website (http://www.viewnetcam.com/).


Confirm the [Viewnetcam.com] services be registered
1
Click [Status] in the Maintenance page.
2
Ensure that [Service contract is already registered.] is displayed in the [Status] of the [Viewnetcam.com] in the [Status] tabs on the Maintenance page.
[Note:]

・If you see anything other than [Service contract is already registered.] in the [Viewnetcam.com] [Status] on the [Status] tab of the Maintenance page, restart the camera and re-access the screen.


Configure port forwarding without using UPnP
If you use a router that does not support UPnP, you must manually configure the port forwarding feature for the router.
1
On the Network Page, press the [Network] tab.
2
In the [Network Settings], select [Static].
3
Check the IP address and port number displayed here, and make corrections if necessary. (This is required when configuring port forwarding for routers.)
4
Press [Set].
5
Configure the port forwarding by referring to your router's instruction manual.

・Use the IP address and port number you checked in step 3 to configure.


・Port forwarding functions may be described as address translation, static IP mascalade, virtual server, virtual server, or port mapping, depending on the router.


[Note:]

・Be sure to set [Auto port forwarding] to [Off] when configuring port forwarding manually for routers.


[Host name]
Enter the host name to use for the dynamic DNS Update service.
Number of characters that can be entered:3 to 250 characters (host name). Enter in (domain name) format
Input Characters:One-byte alphanumeric and one-byte symbols . ‑
[Note:]

・Contact your network administrator for the host name that is available.


[Access interval]
Select an interval to verify the IP address and host name for the dynamic DNS Update service server from the following.
[10min]/ [20min]/ [30min]/ [40min]/ [50min]/ [1h]/ [6h]/ [24h]
[Host name]
Enter the host name to use for the dynamic DNS Update service.
Number of characters that can be entered:3 to 250 characters (host name). Enter in (domain name) format
Input Characters:One-byte alphanumeric and one-byte symbols . ‑
[Note:]

・Contact your network administrator for the host name that is available.


On the Network page, select [Remote Monitoring].
5.1 How to display
5.2 How to operate
Select this setting when connecting the camera directly to Remote Monitoring.
[Note:]

・If you use Remote Monitoring, Image capture size for stream (3) and stream (4) is changed to VGA(640x360).


・Depending on the installed Extension software, internal memory used by Remote Monitoring may be insufficient. Make sure that the remaining RAM space in [Software mng.] tab. of Extension software is at least 15MB. If it is less than 15MB, Remote Monitoring does not operate normally.


・If you are using Remote Monitoring and have installed Extension software, make sure that the remaining RAM is at least 15MB in [Software mng.] section of Extension software section. If it is less than 15MB, Remote Monitoring does not operate normally.


・If you plan to use Remote Monitoring and Extension software at the same time, check to see if Extension software is available at the same time as Remote Monitoring.


・If [Miemasu.net] servicing is enabled, Remote Monitoring is not available.


・[New X Fixed-8MP] [New X Fixed-5M] When [Image capture mode] is set to [60fps Mode] or [50fps Mode], Remote Monitoring is not available.


[Remote Monitoring function]
You can set the Remote Monitoring function (direct camera connection function) to Enable or Disable.
When set to Enable, or if it is already enabled when the camera starts, it will connect to the Remote Monitoring server (https://rms.i-pro.com).
This allows for video streaming to Remote Monitoring, playback and download of video data stored on the SD card, and receiving alarm notifications.
[Note:]

・When you select [Set recommended values], the settings will be adjusted to values suitable for Remote Monitoring connection, depending on the model.


・For details on the settings that will be adjusted when [Set recommended values] is selected, refer to the following link.


 CameraDirect-RemoteMonitoring_webguide_en
[Remote Monitoring registration mail address]
The input field becomes available when you select [Enable] for the [Remote Monitoring function]. Before doing this, you need to access Remote Monitoring (https://rms.i-pro.com) to register your email address and set a password. Enter the email address here that you registered in Remote Monitoring.
[Remote Monitoring password]
The input field becomes available when you select [Enable] for the [Remote Monitoring function]. Before doing this, you need to access Remote Monitoring (https://rms.i-pro.com) to register your email address and set a password. Enter the password here that you registered in Remote Monitoring.
Setting up a direct camera connection
1
Select [Enable] for the [Remote Monitoring function] and enter your email address and password.
2
Click the [Set] button.
Check the alert message and click the OK button.
When [Remote Monitoring function] is set to [Enable], the settings in the following table will be adjusted and fixed, regardless or whether or not the checkbox is selected.
Item
Remote Monitoring Enabled
Audio out
Audio
SD Memory Card File System Format
FAT(FAT16/FAT32/exFAT)
Recording stream
Stream(1)
Image capture size of JPEG(1)
If [Image capture mode] is [16:9 mode]: 640x360
If [Image capture mode] is [4:3 mode]: VGA
Stream transmission of Stream(1), Stream(2)
On
Stream encoding format of Stream(1), Stream(2)
H.265
Image capture size of Stream(4)
If [Image capture mode] is [16:9 mode]: 640x360
If [Image capture mode] is [4:3 mode]: VGA
TCP alarm notification, Additional extended alarm information
On
3
Registration complete
A popup window is displayed. The registration process takes approximately 20 seconds. Once registration is complete, [The registration is successfully completed.] is displayed, and [Remote Monitoring registration status] will show either [Registered (No license is allocated)] or [Registered (License is allocated)].
If the popup is not displayed
If popups are blocked, a notification is displayed in the address bar indicating that the popup was blocked. Allow popups to be displayed. Once this is done, set the [Remote Monitoring function] to [Disable], then switch it back to [Enable], enter your email address and password, and then click the [Set] button.
When registration is complete, close the popup by clicking the [x] at the top-right. Next, click the [Registration status update] button to confirm that [Remote Monitoring registration status] shows either [Registered (License is allocated)] or [Registered (No license is allocated)].
Correcting an incorrectly entered email address or password
Set the [Remote Monitoring function] to [Disable], then switch it back to [Enable], enter the correct email address and password, and then click the [Set] button.
If registration fails

・Check that the network camera is connected to allows external connections.


・Check that the default gateway is set correctly in the [Network] settings.


・Check that the primary server address is set correctly if DNS is set to Manual in the [Network] settings.


・Check that the date and time in the [Basic] settings match the local standard time for the camera's location. 


[Note:]

・For more information about the Remote monitoring supported models, refer to our technical information website <Control No.:C0103>.


Remote Monitoring supported browser
Use Google Chrome or Microsoft Edge to access the system. Firefox may not operate correctly.