10Advanced Alarm Settings [Alarm]

On the Alarm page, you can set alarm operations, alarm images, alarm detection areas, and alarm notification settings using the external I/0 terminals.
The Alarm page consists of the [Alarm] tab, [VMD area] tab, [SCD area] tab, [Audio detection] tab, [Impact Detection] tab, and [Transmission] tab.

10.1[Alarm] for setting alarm operations

On the Alarms page, click the [Alarm] tab. For details on how to display and operate the Advanced menu, refer to the following.
→4.1.1　How to display
→4.1.2　How to operate
This section describes the settings related to the operation when an alarm is detected. For the settings related to the alarm image and output terminal, refer to the following.
→10.4　[Alarm] for setting interlocked alarm operation
→10.2　[Alarm] for setting pins

Alarm

[Terminal 1]
Sets the operation of terminal 1.

・[Off]: Pin functions are not used.

・[Alarm input(TRM1)]: Accepts terminal alarm input.

・[Close]: Alarm is detected when the pin status changes to [Close].

・[Open]: Alarm is detected when the pin status changes to [Open].

・[Close(Continue)]: Alarm is detected when the pin status changes to [Close]. When the pin status is [Close], the alarm is detected periodically at the alarm non-detection interval.

・[Open(Continue)]: Alarm is detected when the pin status changes to [Open]. When the pin status is [Open], the alarm is detected periodically at the alarm non-detection interval.

・[Radar]: Operates as radar alarm input.

・[Cameras]: Operates as an alarm input for the camera.

・[Radar Self check Start]:You can check whether the radar is operating normally.

・[Close]: Radar self-test starts when the pin status changes to [Close].

・[Open]: Radar self-test starts when the pin status changes to [Open].

・[Black & white input]: Accepts black and white switching input. (Switches to black and white when the entry is [On].)

・[Auto time adjustment]: Accepts the time setting by terminal input. If the time difference from the hour (every hour 00 minutes) is within 29 minutes, set to 00 minutes 00 seconds. If the time is less than 5 seconds during SD recording, the time is not changed. When "AUTO TIME ADJUST" is selected, the short-circuit and open selection pull-down menus are displayed.

・[Close]: When the pin status changes to [Close], the watch automatically adjusts the time.

・[Open]: When the pin status changes to [Open], the watch automatically adjusts the time.

[Reference]

・When terminal 1 is selected as [Self-diagnosis start], the result is output to terminal 3 according to the setting.

[Terminal 2]
Sets the operation of terminal 2.

・[Off]：Pin functions are not used.

・[Alarm input (TRM2)]:Accepts terminal alarm input.

・[Short-circuit]:Alarm is detected when the pin status changes to [Close].

・[Open]:Alarm detection is performed when the terminal status changes to [Open].

・[Short (Continued)]:Alarm is detected when the pin status changes to [Close]. When the pin status is [Close], the alarm is detected periodically at the alarm non-detection interval.

・[Open (Continue)]:Alarm is detected when the pin status changes to [Open]. When the pin status is [Open], the alarm is detected periodically at the alarm non-detection interval.

・[Radar]: Operates as radar alarm input.

・[Cameras]: Operates as an alarm input for the camera.

・[Alarm output]:Alarm is outputted according to the content set in [Output terminal].

・[Radar]: Outputs when an alarm is detected by the radar.

・[Cameras]: Outputs when an alarm is detected on the camera.

→10.2　[Alarm] for setting pins

[Terminal 3]
Sets the operation of terminal 3.

・[Off]：Pin functions are not used.

・[Alarm input (TRM3)]:Accepts terminal alarm input.

・[Short-circuit]:Alarm is detected when the pin status changes to [Close].

・[Open]:Alarm is detected when the pin status changes to [Open].

・[Short (Continued)]:Alarm is detected when the pin status changes to [Close]. When the pin status is [Close], the alarm is detected periodically at the alarm non-detection interval.

・[Open (Continue)]:Alarm is detected when the pin status changes to [Open]. When the pin status is [Open], the alarm is detected periodically at the alarm non-detection interval.

・[Radar]: Operates as radar alarm input.

・[Cameras]: Operates as an alarm input for the camera.

・ [Alarm output]:Alarm is outputted according to the content set in [Output terminal].

・[Radar]: Outputs when an alarm is detected by the radar.

・[Cameras]: Outputs when an alarm is detected on the camera.

・[AUX out]:Performs AUX export. Displays the [AUX] in the Live image pages.

[Reference]

・[Radar Self check Output] is displayed only when [Radar Self check Start] is selected at terminal 1.

・In [Self-diagnosis result output], if the input from pin 1 is output to pin 3, it is normal. If the input from terminal 1 is not output to terminal 3, an error occurs.

[Notice]

・The AUX is the camera-terminal that the operator can control (Open/Close) from the Live image pages arbitrarily. For example, if you want to control the lighting in the location where the camera is installed, you can control the camera from a remote location by connecting it to a lighting control device.

[VMD alarm]
Clicking [VMD >>] displays the [VMD area] tab of the Alarms page.
→10.5　[VMD area] to set operation detection

[Scene change detection (SCD) alarm]
Clicking [SCD >>] displays the [SCD area] tab of the Alarms page.
→10.8　[SCD area] to set the disturbance detection area

[Audio detection alarm]
Clicking [Audio detection >>] displays the [Audio detection] tab of the Alarms page.
→10.9　[Audio detection] for configuring sound detection settings

[Shock detection alarm]
Click [Impact Detection Settings] to display the [Impact Detection] tab on the Alarm page.
→10.10　To set impact detection [Impact Detection]

[Command alarm]
Set whether to accept command alarm entry with [On]/[Off].
A command alarm is a function that receives TCP alarm notification notifications from other cameras. When [On] is set, the alarm action can be synchronized with several cameras.

[Reception port]
Set the port number to receive command alarms.
Setting range :1～65535
The following port numbers cannot be set because they are used on this unit.
20、21、22、23、25、42、53、67、68、69、80、110、123、161、162、443、554、995、1883、8883、10669、10670、59000～61000

[Alarm deactivation time]
Set the length of time that the detection operation is not performed after an alarm is detected. For example, if the alarm is set to notify the mobile device or tablet device of the e-mail, this setting can be used to prevent too many e-mails from being sent.

0.5 s、1 ～ 600 s

[Notice]

・Alarm detection time is managed for each alarm type. For example, operation detection and disturbance detection alarms are detected even during the command alarm non-detection time.

[Alarm test]
Clicking [Execute] executes the alarm test function.

[Notice]

・When the alarm test function is executed, this machine detects the command alarm.

It can be used to record SD memory cards triggered by alarm detection and to check notifications to external devices. Use the external device set as the notification destination and the system log of this machine to check related settings.

・The alarm test function cannot be activated more than once within the alarm non-detection time.

10.2[Alarm] for setting pins

On the Alarms page, click the [Alarm] tab. Refer to the User's Manual for details on how to display and operate the advanced settings menu.
Here, you can make settings related to output terminals.

Output terminal

For the output-pin function, the [Terminal 2] or [Terminal 3] in the [Alarm] settings must be set to [Alarm output].

[Terminal output upon alarm detection]:Sets whether to output alarm signals to the output terminals when an alarm is detected.
[On]／ [Off]

[SD memory card error]:Sets whether to output a signal to the output terminal when a warning is detected on the SD memory card.
→ SD Memory Card Alert Detect Condition: SD Memory Card Error (Write Error, Read Error, etc.), 6-Year Runtime, Overwrite Count Exceeded 2000 Times
[On]：When a warning condition is detected, a signal is output to the output terminal, and [Alarm occurrence notification] of the live image is popped over.
[Off]：Stops the detection of a warning condition.

[Important]

・To use this function correctly, format a SD memory card on the Digital Piano before using it.

[Notice]

・Operating hours: 6 years refer to the power-on hours after inserting the SD card into the camera. Overwriting times: 2,000 times is based on the upper limit of the number of rewritable times for professional SD memory cards (MLC types), and the durability is not guaranteed.

・The output terminal and the SD memory card warning use the same output terminal.

・When an alarm or SD memory card warning occurs, the signal is output to the output terminal.

・If a SD memory card warning is detected, [Alarm Notification] pop-over appears in Live image pages. Click the [x] button of [Alarm Notification] to clear the display of [Alarm Notification].

・The output terminal signal output by the SD memory card warning varies depending on the alarm output format setting.
-When latched: Signaling at the output terminal continues while the cause of the SD memory card warning continues even after the indication of [Alarm occurrence notification] is cleared.
-For Pulse: Signal output at the output terminal continues while the cause of the SD memory card warning continues even after the display of [Alarm occurrence notification] is cleared. However, signal output at the output terminal stops when the time set in [Alarm output time] has elapsed.

[Terminal state upon alarm detection]
Sets either [Latch] or [Pulse] as the operation of the output pin when an alarm is detected.
[Latch]:When an alarm is detected, the terminal at the time of alarm output is set to [Terminal action upon alarm detection] until the [x] button in [Alarm Notification] is clicked.
[Pulse]:When an alarm is detected, the time set in [Pulse output width] and the pin at the time of alarm output are set in [Terminal action upon alarm detection]. Click the [x] button of [Alarm Notification] to return the output terminal to the normal state.

[Terminal action upon alarm detection]
Use the [Open] and [Close] buttons to set the output status when an alarm is output from the output terminal.
[Open]：Sets the pin to Open when an alarm is generated (usually Close).
[Close]：Sets the pin to Close when an alarm is generated (usually Open).

[Notice]

・When set to [Open], an alarm is issued for approximately 20 seconds when the unit is turned on.

[Pulse output width]
Sets the duration for which an alarm is output from the output terminal when [Pulse] is selected in [Terminal state upon alarm detection].
Setting range :1～120s

10.3[Alarm] whose AUX name is to be changed

On the Alarms page, click the [Alarm] tab. For details on how to display and operate the advanced settings menu, refer to the User's Manual.
You can rename the [AUX], [Open], and [Close] of the Live image pages.

AUX name
[AUX (Up to 10 characters)]
Enter the name of the [AUX] for the Live image pages.
Characters that cannot be entered:Half-pitch symbols "&
[Open (Up to 5 characters)]
Enter the name of the [Open] in the [AUX] of the Live image pages.
Characters that cannot be entered:Half-pitch symbols "&
[Close (Up to 5 characters)]
Enter the name of the [Close] in the [AUX] of the Live image pages.
Characters that cannot be entered:Half-pitch symbols "&

[Notice]

・The AUX name can be changed when [PIN 3] of the [Alarm] setting is set to [AUX output].

・The AUX is the camera-terminal that the operator can control (Open/Close) from the Live image pages arbitrarily. For example, if you want to control the lighting in the location where the camera is installed, you can control the camera from a remote location by connecting it to a lighting control device.

10.4[Alarm] for setting interlocked alarm operation

On the Alarms page, click the [Alarm] tab. Refer to the User's Manual for details on how to display and operate the advanced settings menu.
This section describes the settings for functions that operate in conjunction with alarms.

[Alarm E-mail notification]
When [E-mail notification setup >>] is clicked, the setting window related to the e-mail when an alarm occurs is displayed in a separate window.
→10.4.1　Set Email Sending When an Alarm Occurs

[Alarm image recording(SD memory card)]
Clicking [SD memory card setup >>] displays a separate window for setting the SD memory card recording when an alarm occurs.
→10.4.2　Settings related to SD memory card recording when an alarm occurs

[TCP alarm notification]
Clicking [TCP alarm notification setup >>] opens a separate window with settings for sending TCP alarm notification notifications when alarms occur.
→10.4.3　Settings related to TCP alarm notification notification when an alarm occurs

[HTTP alarm notification]
Clicking [HTTP alarm notification setup >>] displays the setting window for sending HTTP alarm notification when an alarm occurs in a separate window.
→10.4.4　Settings related to HTTP alarm notification when an alarm occurs

[SNMP transmission upon alarm detection]
Clicking [To SNMP setting] displays the setting window for sending SNMP when an alarm occurs in a separate window.
→10.4.5　Setting for SNMP Send When an Alarm Occurs

10.4.1Set Email Sending When an Alarm Occurs

On the Alarms page, on the [Alarm] tab. Click [E-mail notification setup >>] in the [Camera action on alarm].
→10.4　[Alarm] for setting interlocked alarm operation
For the setting method, refer to the user manual.

10.4.2Settings related to SD memory card recording when an alarm occurs

On the Alarms page, on the [Alarm] tab. Click [SD memory card setup >>] in the [Camera action on alarm].
For the setting method, refer to the following.
→7.2　Setting an SD Memory Card [SD Memory Card]

10.4.3Settings related to TCP alarm notification notification when an alarm occurs

On the Alarms page, on the [Alarm] tab. Click [TCP alarm notification setup >>] in the [Camera action on alarm].
→10.1　[Alarm] for setting alarm operations
For the setting method, refer to the following.
→10.11.1　Setting Up TCP alarm notification Notifications

10.4.4Settings related to HTTP alarm notification when an alarm occurs

On the Alarms page, on the [Alarm] tab. Click [HTTP alarm notification setup >>] in the [Camera action on alarm].
→10.4　[Alarm] for setting interlocked alarm operation
For the setting method, refer to the following.
→10.11.2　Setting HTTP Alarm Notification

10.4.5Setting for SNMP Send When an Alarm Occurs

On the Alarms page, on the [Alarm] tab. Click [To SNMP setting] in the [Camera action on alarm].
→10.4　[Alarm] for setting interlocked alarm operation
For the setting method, refer to the following.
→11.2.2　Set the SNMP

10.5[VMD area] to set operation detection

On the Alarms page, click the [VMD area] tab. For details on how to display and operate the advanced settings menu, refer to the User's Manual.
Here, you can set the area for detecting motion of an object using the Motion Detector function. When the movement of an object is captured within the specified area, an alarm operation is performed.

[Important]

・[Alarm Notification] is displayed for confirmation when an object movement is detected using the Motion Detector function.

→3.2.2　About Live image pages

・[Alarm Notification] is also displayed when an alarm input is accepted by the terminal alarm or when a command alarm is accepted.

・Notifications may be delayed depending on the network environment.

・When [Intelligent Auto] is set to [On], an operation detection alarm may be generated due to changes in the brightness of the whole picture depending on the object conditions. In this case, make one of the following settings.
-Set [Illumination detection suppression] in the operation detection area to [On].
-Adjust the slider bar of [Detection sensitivity] in the motion detection area to [Low].

・The Motion Detector function is not designed to prevent theft, fire, etc. We assume no responsibility whatsoever for any accident or damage that may occur.

[Notice]

・This function is the function used by the built-in camera.

Set the motion detection area.

[Area]
If an operation detection area is selected in the image, the settings are made in order from area 1.

[Status]
Set whether to enable or disable motion detection.
[Enable]:Performs motion detection.
[Disable]:Do not perform operation detection.

[Detection area]
Use the slider bar to set the area in the motion detection area that detects the movement of the object. The lower the setting, the smaller the motion of the object. The current setting (1 to 10) is displayed to the right of the slider bar.

[Detection sensitivity]
Use the slider bar to set the sensitivity for detecting movement in the area. Each area can be set individually. The higher the setting, the easier it is to detect the movement.
The current setting (1 (low) to 15 (high)) is displayed below the slider bar.

[Delete] button
Click the button of the area you want to delete to delete the area frame.

[Light detection control]
Use [On]/[Off] to specify whether to prevent motion detection due to changes in lighting brightness, etc.

[Important]

・It may not be possible to suppress the illumination when the brightness and other changes are small.

・If [On] is set to suppress illumination and object with motion is detected, motion detection may not be performed.

・If [Camera title on screen display] is set to [On], the accuracy of motion detection may be reduced.

Add motion detection information

[Information addition]
Use the On/Off to specify whether or not to send the superimposed image data by adding operation detection information to the image. Operation detection information can be used by some of our network disk recorders search functions. For details of the functions and settings, refer to the instruction manual of the device to be connected.

10.6[VMD area] to set operation detection area

Set the operation detection area.

[Important]

・All alarms are not detected while changing settings on the setting screen. Close the setting screen after completing the setting.

[Notice]

・This function is the function used by the built-in camera.

Set the motion detection area setting screen

1

If you specify an area by dragging over the image, the specified area is set to area [1(White)] and a frame is displayed.
Areas are set in order from area number 1. The color next to the area number indicates the color of the corresponding frame. Also, the [Status] of the frame you want to set for the area will be [Enable].

2

Set the [Detection area] [Detection sensitivity] with the slider bar. For information about [Detection area] [Detection sensitivity], see the following:
→10.7　[SCD area] for configuring disturbance detection
The [Detection area] displays the motion detection status for the displayed area and detection sensitivity. Modify the area or [Detection area] [Detection sensitivity] as needed.

3

When you have finished configuring the settings, press [Set].

[Important]

・Settings cannot be confirmed unless [Set] is clicked.

4

To disable the operation detection area, change the [Status] of the corresponding area to [Disable], and then click the [Set] button. The disabled frame color becomes a dotted line.
When disabled, no alarm occurs even if there is a change in the area.

5

To delete the operation detection area, click the [Delete] button of the area to delete, and the frame of the deleted area will be deleted.

6

Clicking the [Set] button. The settings will be applied to this unit.

10.7[SCD area] for configuring disturbance detection

This section describes the settings related to the disturbance detection function.
When the interference detection function is used, the alarm is activated when the object changes as the machine is covered with a cloth, lid, etc., or the direction of the machine is changed. One area can be set. When the disturbance is detected within the set area, the alarm is activated.

[Important]

・The disturbance detection function will not work for a while in the following cases:
-After power-on
-After changing the disturbance detection setting
-When the angle of view of this machine changes

・[Alarm Notification] is displayed for confirmation when a disturbance is detected using the disturbance detection function.

→3.2.2　About Live image pages

・[Alarm occurrence notification] is also displayed when an alarm input is accepted by the terminal alarm or another alarm such as operation detection alarm occurs.

・Interference detection may not be detected or may be erroneously detected in the following cases:
-When only a part of the screen is covered, or when the cover is transparent
-If your object is similar to the one before and after you can change the camera's orientation
-When Privacy Zone is set

・When the color of the image is close to monochrome, it is difficult to detect the disturbance detection. If disturbance detection is difficult to detect, increase the [Detection sensitivity] setting for the disturbance detection function or increase the area setting for the disturbance detection function.

・If the [Intelligent Auto] is set to [On], an Obstruction Detection alarm may be generated depending on the object conditions, because the brightness of the whole picture changes. In this case, make one of the following settings.
-Set the [Detection sensitivity] low.
-You set a longer [Detection time].

・The disturbance detection function is not designed to prevent theft, fire, etc. We assume no responsibility whatsoever for any accident or damage that may occur.

[Notice]

・This function is the function used by the built-in camera.

Set the disturbance detection area setting screen

[Area]
Set the disturbance detection area in the image.

[All areas]
Click to set the entire area as the disturbance detection area.

[Status]
Set whether to detect disturbance using [Enable]/[Disable].
[Enable]: Performs disturbance detection.
[Disable]: Denial detection is not performed.

[Detection area]
Set the area in [Small]/[Medium]/[Large] to detect the movement of the object within the disturbance detection area.

[Detection sensitivity]
Select [Very Low]/[Low]/[Medium]/[High] for detecting disturbance within the area.

[Detection time]
Sets how long it takes to activate the disturbance detection alarm after the object changes. If the object changes only continuously within the specified time, the alarm is activated.
[3s]／ [5s]／ [10s]／ [30s]／ [1min]

[Delete] button
Click to delete the area frame.

Addition of disturbance detection information

[Information addition]
Use the [On] and [Off] buttons to specify whether or not to send the superimposed image data by adding disturbance detection information to the image.

[Notice]

・The additional disturbance detection information is not used in our network disk recorders (as of November 2025).

10.8[SCD area] to set the disturbance detection area

1

Set the disturbance detection area.

[Important]

・All alarms are not detected while changing settings on the setting screen. Close the setting screen after completing the setting.

[Notice]

・This function is the function used by the built-in camera.

2

Clicking [All areas] selects the entire area as the disturbance detection area and displays a frame around the entire screen. Also, [Status] is set to [Enable].

If you drag the mouse over the image and specify an area, the specified area is set to the area (white) and a frame is displayed. Also, [Status] is set to [Enable].

Set the [Detection area] [Detection sensitivity] [Discovery Times]. For details on [Detection area] [Detection sensitivity] [Detect Time], refer to the following.
→10.7　[SCD area] for configuring disturbance detection
Change the settings of the area or [Detection area] [Detection sensitivity] [Discovery Times] as required.

4

When you are done, press [Set].

[Important]

・Settings cannot be confirmed unless [Set] is clicked.

5

If you want to disable the disturbance detection area, change the [Status] to [Disable] and press [Set]. When clicked, the disabled frame color becomes a dotted line. When disabled, no disturbance detection alarms are generated.

6

If you want to remove the intrusion detection area, press [Delete]. Click to erase the area frame.

[Notice]

・If you want to reconfigure the disturbance detection area, you must clear the area frame by clicking the [Delete] button.

7

Clicking the [Set] button. The settings will be applied to this unit.

10.9[Audio detection] for configuring sound detection settings

On the Alarms page, click the [Audio detection] tab. For details on how to display and operate the advanced settings menu, refer to the User's Manual.
Here, you can make settings related to sound detection.

[Important]

・When audio is detected using the sound detection function, [Alarm Notification] is displayed to indicate that the audio has been detected.

・[Alarm Notification] is also displayed when an alarm input is accepted by the terminal alarm or when a command alarm is accepted.

・Notifications may be delayed depending on the network environment.

・The sound detection function is not suitable for applications where high reliability is always required (systems designed to prevent this). We assume no responsibility whatsoever for any accident or damage that may occur.

[Audio detection]
Use the On/Off to specify whether to perform tone detection.
[On]：Sound detection is performed.
[Off]：Sound detection is not performed.

[Detection sensitivity]
Select the sensitivity of the detection from the [Low] [Medium] [High].

10.10To set impact detection [Impact Detection]

Click the [Impact Detection] tab on the Alarm page. For details on how to display and operate the advanced settings menu, refer to the User's Manual.
This section describes how to set up impact detection.

[Important]

・When an impact is detected using the impact detection function, [Alarm occurrence notification] is displayed so that it can be understood that the impact is detected.

・All alarms are not detected while changing settings on the setting screen. Close the setting screen after completing the setting.

・[Alarm Notification] is also displayed when an alarm input is accepted by the terminal alarm or when a command alarm is accepted.

・Notifications may be delayed depending on the network environment.

・The impact detection function is not suitable for applications where high reliability is always required (systems designed for prevention). We assume no responsibility whatsoever for any accident or damage that may occur.

[Impact detection]
Use the On/Off to set whether or not to perform impact detection.
[On]：Performs impact detection.
[Off]：Does not perform impact detection.

[Detection Level]
Use the slider bar to set the threshold at which the impact is detected.
You can adjust the value from 1 to 255. Moving it in the [+] direction will reduce the sensitivity of the impact detection, allowing you to detect only large impacts. [-] If you move it in the direction, the sensitivity to detect an impact becomes strong, and you can also detect a small impact.

[Notice]

・When an impact is applied to the camera while [Impact Detection] is set to [On], a blue bar indicating the impact intensity is displayed. The maximum impact received by the camera is displayed in the [Maximum]. Use this as a guide when setting the [Detection Level]. The displayed [Max.] returns to 0 when [Reset] is pressed.

10.11[Transmission] for setting the alarm notification

On the Alarms page, click the [Transmission] tab. For details on how to display and operate the advanced settings menu, refer to the User's Manual.
This section describes the settings related to TCP alarm notification notifications and HTTP alarm notifications.

10.11.1Setting Up TCP alarm notification Notifications

TCP alarm notification Notification

[TCP alarm notification]
Specify whether to perform TCP alarm notification notification in the On/Off in the following cases:

・When an alarm occurs (TCP alarm notification notification destination [Alarm] field)

・When the remaining space on the SD memory card is notified (TCP alarm notification notification destination [Diag.] field)

・When there is insufficient free space on the SD memory card. (TCP alarm notification notification destination [Diag.] field)

・SD memory card recognition error (TCP alarm notification notification destination [Diag.] field)

・SD memory card write failure (TCP alarm notification notification destination [Diag.] field)

[Notice]

・TCP alarm notification notifications are notified in the order from [Notification Destination 1] (only for the notification destinations checked in the [Alarm] or [Diag.] field).

[Additional alarm data]
Use the On/Off to set whether to notify the operation detection alarm detection area number with TCP alarm notification.

[Destination port number]
Set the receiving port number of the TCP alarm notification notification destination.
Setting range :1～65535
The following port numbers cannot be set because they are used on this unit.
20、21、22、23、25、42、53、67、68、69、80 110、123、161、162、443、554、995、1883、8883、10669、10670、59000～61000

[Retry times]
Sets the number of retries when TCP alarm notification notification cannot be performed.
Setting range :0～30

TCP alarm notification notification destination

[Destination 1] ～ [Address 48]
Sets the TCP alarm notification notification destination by IP address/hostname. Up to 48 destinations can be set.
[Alarm] field:Check this item to notify you when an alarm occurs.
[Diag.] field:When this checkbox is marked, the following errors will be reported: SD memory card remaining space notification, SD memory card insufficient space, SD memory card recognition error, and SD memory card write error.
[Transmission address] field:Enter the IP address/hostname of the notification destination.
Available Characters :Half mark alphanumeric characters and marks : . _ ‑
If you want to delete the set notification destination, press the [Delete] key of the notification destination you want to delete.

[Notification per Camera]
Set whether to set send by camera using the On/Off.
When [Notification per Camera] is set to [On], an alarm generated by the radar is notified when [Radar] is selected, and an alarm generated by the camera is notified when [Cameras] is selected in the same way.

[Notification per Radar detection/VMD area]
Select On/Off to enable or disable the Radar Detection/Motion Detection Area Sending setting.
When [Notification per<br>Radar detection/VMD area] is set to [On], the alarm notification is executed only when [Alarm Area No.] matches [Alarm area] number set for Radar Detection Alarm or Operation Detection Alarm.
Notification of alarms other than radar detection alarm and motion detection alarm is not executed.
When using the send by radar detection/motion detection area function, select one of the detection objects in the alarm area of radar detection, and set the status of the alarm area in motion detection to [Enable].

[Alarm Area No.]
Setting range :1～8

[Important]

・If you enter a hostname for the [Transmission address], you must configure the DNS in the [Network] tab on the Network page.
→10.11.2　Setting HTTP Alarm Notification

・Check that the notification destination is set correctly. If there are no notification destinations, delays in TCP alarm notification notifications or missing transmissions may occur.

10.11.2Setting HTTP Alarm Notification

HTTP alarm notification

[Destination 1] ～ [Address 5]
Set the IP address/hostname of the HTTP server to be notified of the HTTP alarm. You can set up to 5 recipients.
Available Characters :Half mark alphanumeric characters and marks : . _ ‑
Input example:
Http://IP address:Port number or http://Hostname:Port number
Https://IP address:Port number or https://Hostname:Port number

[Alarm] field
When this checkbox is marked, HTTP alarm notification is performed when an alarm occurs.

[Diag.] field
When this checkbox is marked, HTTP alarms are notified when the remaining space of the SD memory card is notified, when there is insufficient free space on the SD memory card, when an error occurs during SD memory card recognition, when the Extension software trial period expires, or when an error occurs during SD memory card writing.

[Delete] button
Clicking this button deletes all notification destinations, user names, passwords, notification data, and advanced settings for that item.

[Username]
Enter the username for accessing the HTTP server.
Number of characters that can be entered:0 to 63 characters
Characters that cannot be entered:Two-byte or one-byte symbol"&: ; ￥

[password]
Enter the password for accessing the HTTP server.
Number of characters that can be entered:0 to 63 characters
Characters that cannot be entered:Two-byte or one-byte symbol"&

[Notice]

・Authenticate Basic or Digest by requesting authentication from the HTTP server.

[Notification data]
Set the notification content to be attached to the back of the HTTP server set to [Destination 1] ~ [Address 5].
Available Characters :Half mark alphanumeric characters and marks

[Notice]

・Enabling the HTTP alarm function may cause the credentials (username and password) of the HTTP server to be compromised on the network when an alarm is sent to the HTTP server.

・The total number of characters of the notification destination (including [http://]) and [Notification data] is limited to 256 characters.

・Be sure to enter [Notification data] beginning with a slash (/).

・If the HTTP alarm notification fails, it is recorded in the system log.

・If [Notification data] is left blank and [Set] is pressed, [/cgi‑bin/comalarm.cgi?CMD=01] is also set.

Example :
If [http://192.168.0.100] is set as the notification destination and [/cgi‑bin/comalarm.cgi?CMD=01] is set as the [Notification data], the HTTP alarm notification "http://192.168.0.100/cgi‑bin/comalarm.cgi?CMD=01" is executed.