1Introduction

This manual explains how to register extension software AI Occupancy Detection application WV-XAE207W (hereinafter referred to as this product) with AI network cameras (sold separately, hereinafter referred to as camera), the settings required prior to starting operation, and how to operate AI network cameras. The camera must be registered before use. Be sure to read the camera's instruction manual when using the camera. The settings shown in this manual may differ depending on the camera model used and the i-PRO Setting Tool version (hereinafter referred to as iCT).

1.1Product Overview

This product is software that makes it easier to use your camera.By installing this product on your camera, you can use the　based on the setting conditions of the AI Occupancy Detection function, alarms can be notified to external systems such as WV-ASM300/WV-ASM300W (option) and WJ-NX series network recorders (option).

・This product is required for each camera.


・See the URL below for information such as the models supported by this product, the software version, etc.


→Technical Information <C0103>

※<Control number: Cxxxx> The number used when searching for the appropriate information on our support website.

1.2Features

●

This product can be integrated additionally into an existing i-PRO surveillance system.


(Only network cameras and this product are to be added.)




●

This product notifies the specified notification destination of alarms when the set conditions are reached.


●

This product sends the information about the number of objects detected periodically to the specified transmission destination.


●

This product has the following features.


①

The deep learning technology and our proprietary image processing technology can detect occupancy by detecting objects.


②
You can detect occupancy with the camera alone just by installing this product on the camera.

1.2.1Specifications

　

Occupancy detection method The system detects if the count exceeds a set number for a certain period of time within the target area, or if it falls below the set number.


　

Detectable angle of view Depression angle 45° or less


　

Maximum count of objcts      40


　

Number of settable areas Up to 4


　

Detection time 1-600 sec/area


　

HTTP Connection Settings 4 transmission destinations; transmission interval: 1/5/10/15/30/60 sec; SSL supported


　

Installation location people: Indoor (Including the under-eave area not exposed to direct sunlight)


　　　　　　　　　　　　　　 vehicles /bicycles / AI onsite-learning objects: Indoor (Including the under-eave area not exposed to direct sunlight) / Outdoor


　

Illuminance 50 lux or above (around the subject)

* See the URL below for "Body size" information.
→Technical Information<Control No.: C0320>

1.3Before using this product

Occupancy may not be detected correctly in the following cases since it may be difficult to detect a object, or false detection may occur.
●
The object is out of focus.
●
The object is shaking.
●
The object overexposed or washed out.
●
Only 2/3 or less of the part above a person's shoulders or object is shown.
●
The camera imaging angle is at a depression angle of 45° or above.
●
Only a part of the object is shown in the privacy zone set from the "Setup" menu > "Image/Audio" > "Image quality" on the camera.
●
The object is too close to the camera.
●
The object is too small (size less than the specified shoulder width).
●
It may detect to dolls and posters.
●
It may not be possible to correctly detect a person lying down or falling down.
Other cautions are explained below.
●
If the number of people shown in the camera exceeds 40, correct occupancy detection will not be possible since some of the objects cannot be detected.
●
Depending on the camera you are using, the transmission frame rate may be limited when using the AI Occupancy Detection application. Refer to the URL below for details.
→Technical Information <Control No.: C0103>
●
When AI Occupancy Detection Application is running, if you change the camera's image mode or stream settings,the application will restart. If the setting screen or demo screen of AI Occupancy Detection Application is open, please reload it.
●
If you have set a privacy zone, you cannot detect object within the privacy zone.
●
The message ID of TCP alarm notification is "98" for Area 1, "99" for Area 2, "100" for Area 3, and "101" for Area 4.
●
When using multiple TCP alarm notification simultaneously, if one TCP alarm notification is received after setting the "Alarm mask time" of the WJ-NX series network recorder, no other TCP alarm notification will be received during the "Alarm mask time".
●
For TCP alarm notification settings, refer to ‘TCP alarm notification’ in the Operating Instructions of the camera.
●
Use Mozilla Firefox, Google™ Chrome™ and Microsoft edge to display the setting screen or demo screen. Internet Explorer is not supported.
●
The demo screen can be displayed on only one browser. It does not support simultaneous access by multiple browsers.
●
If the data encryption is set to "On", the demo screen image will not be displayed.
●
The detection frame is not displayed when the setting screen is connected via HTTPS.
●
The demo screen does not support HTTPS connection.
●
When used simultaneously with other extension software functions , the position of the person may be significantly misaligned with the frame on the demo screen.
●
Depending on various installation conditions and usage environment such as the brightness of the location and the movement of the object, object may be difficult to detect, or it may not be detected, or it may malfunction. Please evaluate the installation location before installing.
●
We shall not be liable for any inconvenience, damage or loss caused by setting the AI Occupancy Detection function or as a result thereof.
●
Please read the Operating Instructions of your camera for the disclaimer, protection of personal information, trademarks and registered trademarks, and copyright.

1.4About the Operating Instructions

In this manual, WV-ASM300 and WV-ASM300W are referred to as WV-ASM300