3Basic settings

The procedure for configuring Basic settings is as follows.

①

Open the setting menu
→3.1　Open the setting menu

②

Select the operation
→3.2　Select the operation

③

Set the AI-VMD
→3.3　AI motion detection setting

④

Set the count function
→3.4　Set the count function

⑤

If you want to set the AI-VMD detection sensitivity, detection duration, and size of the human you want to detect:
Make detailed settings
→3.5　Detailed setting (if necessary)

⑥

Set a schedule
→3.6　Schedule setting

⑦

Set an alarm
→3.7　Alarm setting

For settings on cameras that support Internet Explorer, the display plug-in software [Network Camera View 4S (ActiveX)] must be installed on the PC in advance.
For details, refer to the Operation and Settings section of the camera's operation manual.

3.1Open the setting menu

When the AI motion detection application is installed, the AI-VMD menu is added to the Cameras [Setup] menu > [Ext. software] page > [Software mng.] tab.
Clicking the [AI-VMD] tab or the [Setup >>] button moves the tab to the [AI-VMD Settings] tab.

The [AI-VMD Settings] window has six setup windows: Select [➀ Operation selection], [➁ AI motion detection Setting], ③ [Count function Setting], [④ Detailed setting], [⑤ Schedule setting], and [⑥ Alarm setting].

If you do not select [➀ Operation selection], the settings after [➁ AI motion detection Setting] cannot be made.

3.2Select the operation

Status
The status of the AI motion detection application is displayed.
When it is running, the status is displayed as [Enable], when it is stopped, the status is displayed as [Disable].
Operation is started by setting [Mode Selection], and can be stopped by clicking [Stop AI-VMD] button.

Mode selection
Select the image angle mode of the camera to be used.
There are two modes, Normal angle mode and Perpendicular angle mode, and the following functions are available for each mode.

●

Normal angle mode: AI motion detection, count function (Detection object: Human, vehicles, two-wheel vehicles)

●

Perpendicular angle mode: AI motion detection, count function (Detection object: Human)

・If you want to count people more accurately, we recommend Perpendicular angle mode. However, the camera must be positioned directly downward.

・When using the Perpendicular angle mode at the same time as a extension software other than this product, pay attention to the condition of use of the extension software that is used at the same time.

3.3AI motion detection setting

Set the area for detecting moving object by AI-VMD and the detection condition.
Select the Detection object of the Detection area from the human, car, and motorcycle. Select INTRUDER, LOITERING, DIRECTION, or CROSS LINE as the Detection mode. You can set up to 8 Detection area and 8 mask areas for each setting. You can set up to two combinations of areas and detection conditions and save them as [Detection program 1] and [Detection program 2].

a: alarm occurrence notification area, b: drawing area, and c: detection condition setting

3.3.1Alarm notification area

When AI-VMD detects moving bodies, the alarm icon and the icons for the four detection modes turn on. Click the alarm icon to clear the alarm state and turn off all the icons.

①

Alarm ICON

②

CROSS LINE

③

INTRUDER

④

LOITERING

⑤

DIRECTION

3.3.2Drawing area (for setting the detection areas)

a: camera image screen, b: Paint type, c: Demo screen display, d: Position selection

Camera video screen
This window draws the detection area or detection lines.
To draw, select the [Detection area (polygon)] or [CROSS LINE] icons you want to draw from the [Paint type] and drag them to the [Camera video screen].
An alarm is generated when the actuator is identified within the Detection area set by drawing.
An alarm is generated when the movement traverses the set detection line.

Paint type
Click the icon to select the drawing format.

①

CROSS LINE: Draws detection lines for CROSS LINE.

②

Detection area: Draws Detection area as a polygon (up to 16 sides).

③

Mask Area (polygon): Draws the mask area as a polygon (up to 16 sides).

④

Detection area: Select the drawn Detection area.

⑤

Mask Area (Select): Select the drawn mask area.

⑥

Delete: Deletes the selected Detection area and mask areas.

⑦

All Delete: Deletes all drawn Detection area and mask areas.

・When you draw a Detection area (polygon) or mask area (polygon), you complete the area setting by selecting the start point at the end.

・The Detection area, detection line, and mask area selected in the Detection area, Mask Area (Select) can be changed in size, length, and shape by dragging the corners and end points of the frames. You can also move by dragging the inside of the frame or the line.

・To delete a Detection area or detection line, when several Detection area or detection lines overlap, left-click the mouse in the overlapping area to switch the selected frames in turn.

・The center under the detection frame is the position of the detection frame. Set Detection area so that the position of this detection frame is Detection area.
Refer to the following pages for the detection frame.

→6　Operation

・Multiple Detection area, detection lines, and mask areas cannot be selected at the same time.

・By default, the entire drawing area is set to Detection area.

・If you change the [Image capture mode] [Image rotation] in the [Setup] menu of the camera, the Detection area and mask area settings return to the default settings.

・The mask area is the same in [detection program 1] and [detection program 2], and the count function setting.

Demo screen display
Click to display the demo screen.

Select a preset position (for PTZ cameras only)
For PTZ cameras, set the Detection area and mask area for each preset position.
Select the preset position to be set as follows.

Preset positions 1 to 16: Preset positions 1 to 16

Out of preset position: Preset positions 17 to 256 and out of preset position (common)

Start (PTZ camera only)
Click to move to the selected preset position.

No alarm is notified during camera PTZ operation.

3.3.3Detection condition setting

Detection program 1 and Detection program 2
Select the [Detection program 1] and [Detection program 2] tabs to set one or two detection criteria.
The two conditions can be executed simultaneously or separately, depending on the scheduling.
See the following pages for schedule settings.
→3.6　Schedule setting

・In the initial setting of the schedule, Detection program 1 and Detection program 2 are always valid

・When using i-PRO Active Guard, only alarms generated by Detection program 1 will be notified as events.

Detection area
Up to eight Detection area and detection lines are distinguished by line colors.
The colors of drawing lines are set in order from [1 (White)].

Detection object
For each Detection area, check the objects (moving objects) you want to detect.
Three types of Detection object are available:

・

Humam

・

Vehicle (ordinary car, bus, truck)

・

Biycle (Motorcycle, bicycle)

Default setting: Human, Bicycle, and Vehicle are checked

・The three Detection object can also be used in combination.

・If you want to detect all motion, check all three.

・If more than one Detection object is selected, the result is output in the order of precedence of the vehicles, bicycles, and humans. Unchecking for unnecessary Detection object may result in better results. For example, if a human stands in front of a car, the human may be output as a vehicle. Unchecking the vehicle may result in output as a human.

Detection mode
Select the detection modes for the set Detection area and detection lines.

INTRUDER: Detects that moving bodies have intruded the detection area.

LOITERING: Detects that moving bodies have loitered in the detection area for the fixed time.

DIRECTION: Detects that moving bodies have moved in the direction you specified within the detection area.

CROSS LINE: Detects that moving bodies have crossed the detection line in the direction you specified.

Default setting: INTRUDER

Direction setup
If Detection mode is [DIRECTION] or [CROSS LINE], set the detection orientation.

For [DIRECTION], you can choose from the following eight directions:

Upper: Detected when moving upward.

Upper right: Detected when moving in the upper right direction.

Right: Detected when moving in the right direction.

Lower right: Detected when moving in the lower right direction.

Lower: Detected when moving downward.

Lower left: Detected when moving in the lower left direction.

Left: Detected when moving to the left.

Upper left: Detected when moving in the upper left direction.

Default setting: Left

For [CROSS LINE], select from the following three directions.

A→B: Detected when moving from A to B.

B→A: Detected when moving from B to A.

A⇔B: Detected when moving from A to B or from B to A.

Default setting: B→A

[Set] buttons
Click to save the contents of the currently displayed area settings tab.

3.3.4Area setting procedure

1.

Confirm that the [AI motion detection Settings] window is selected.

2.

Ensure that the [Detection program 1] tabs are selected.

3.

Draw an area for detection (hereinafter referred to as "Detection area") in the drawing area.
Draw a location (hereinafter referred to as the mask area) that you do not want to detect in the Detection area.
Eight Detection area and eight mask armatures can be set respectively.

4.

Configure four Detection mode for each Detection area: INTRUDER, LOITERING, DIRECTION and CROSS LINE, respectively.

5.

If Detection mode is [DIRECTION] or [CROSS LINE], configure [Direction setup].

6.

Save the [Detection program 1] detection condition by clicking [Setup].

7.

Select the [Detection program 2] tabs and save the [Detection program 2] detection criteria in steps (3) to (6).

3.4Set the count function

Configures the count function.
Select a Detection object of humans, vehicles, and bicycles as the lines. You can set up to 8 lines and up to 8 mask areas for each setting.

a: Camera video screen, b: Paint type, c: Demo screen display, d: Line setting

Camera video screen
This screen draws the detection line.
To draw, select the [Detection line] icon from the [Paint type] and drag the icon to the [Camera video screen].
When the set detection line is crossed, the number of movement is counted.

Paint type
Click the icon to select the drawing format.

①

Detection Line: Draws a detection line for count function.

②

Mask Area (polygon): Draws the mask area as a polygon (up to 16 sides).

③

Detection line (Select): Select the drawn detection line.

④

Mask Area (Select): Select the drawn mask area.

⑤

Delete: Deletes the selected Detection area and mask areas.

⑥

All Delete: Deletes all drawn Detection area and mask areas.

Demo screen display
Click to display the demo screen.

3.4.1Line setting

Detection object
For each Detection area, select the object (moving object) that you want to detect.
Three types of Detection object are available:

・

Humam

・

Biycle (Motorcycle, bicycle)

・

Vehicle (standard car, bus, truck)

Default setting:
When Perpendicular angle mode is selected: Human
When Normal angle mode is selected: Vehicle

Detectable objects differ depending on the selected mode.
Perpendicular angle mode: Human
Normal angle mode: Human, vehicles, two-wheel vehicles

Direction setup
Specifies the direction in which to count.

・

Inward

・

Outward

・

In/Outward

Default setting: In/Outward

Detection line name
The name of each line is set to 20 characters or less. The configured Detection line name is displayed on the i-PRO Active
Guard dashboard.
Default setting: Line 1 to 8
Inputtable Characters: One-byte symbol ["][&]

[Set] button
Click to save the contents of the currently displayed Line Settings tab.

3.4.2HTTP transmission

Set the Transmission destination (1 to 4) and notification intervals for HTTP to send counts.

Transmission destination 1, Transmission destination 2, Transmission destination 3, Transmission destination 4
You can notify the count data individually to up to four locations. The settings of the four notification destinations are the same.

Transmission
When the check box is checked, the message is sent.
Default setting: Unchecked

Destination addresses
Enter the IP address or host name of the notification destination. Enter up to 128 half-pitch alphanumeric characters and symbols.
Default setting: blank

Destination pathname
Enter the path name of the notification destination. Enter up to 128 half-pitch alphanumeric characters and symbols.

SSL
Select whether to use SSL for notification.
Default setting: On

Destination port number
Set the port number of the notification destination.
1 ～ 65535

User name
Enter the user name for authentication with the notification destination. Enter up to 128 half-pitch alphanumeric characters and symbols.

Transmission Password
Enter the password for authentication with the notification destination. Enter up to 63 half-pitch alphanumeric characters and symbols.

Transmission interval
Select the time interval to send.

5 s, 10 s, 15 s, 1 min, 5 min, 10 min, 15 min, 30 min, 60 min

Default setting: 5 min

3.4.3MQTT transmission

Set the notification content and notification interval for MQTT to send count data.

Transmission
When the check box is checked, the message is sent.
Default setting: Unchecked

To the MQTT transmission setting
Click this button to display the MQTT setting screen of the camera.

Topic
Enter the name of the MQTT topic to be sent. Enter up to 128 half-pitch alphanumeric characters and symbols.

QoS
Select the level of QoS from 0, 1 and 2. Communication quality is high with 0<1<2.

0:QoS0 delivers up to one message. Messages are not guaranteed to reach the server.

1:In QoS1, messages are delivered at least once. Messages are guaranteed to reach the Transmission destination, but may be duplicated.

2:QoS2 delivers the message exactly once. Messages are guaranteed to arrive only once without excess or deficiency.

Default setting: 1

Retain
Check this box to have the last notified message saved on the MQTT server.
Default setting: Unchecked

Transmission interval
Select the time interval to send.

5 s, 10 s, 15 s, 1 min, 5 min, 10 min, 15 min, 30 min, 60 min

Default setting: 5 min

3.4.4Heat map setting

Set the heat map function to aggregate the count data of the human and visualize the passage and retention as a heat map.

Heat Map Funcion
Select whether to use the heat map function or not.
Default setting: Off

Display a confirmation screen
When [Execute] is clicked, a confirmation window is displayed in another window.
The confirmation screen displays the latest heat map.

Confirmation window for heat map setting

Displaying map information
Displays the latest pass map or residence map. Immediately after opening the confirmation screen, the pass map is displayed.

Date and time of the displayed heat map information
The date and time when the heat map information displayed on the confirmation screen was measured is displayed.

Type of heat map
Displays the type of heat map information displayed on the confirmation screen.
Passage map and Loitering map

Upper limit
Displays the area where a value exceeding the value set was counted in red.
This value represents "The number of people passing through [person]" in the case of a passing map, and "The average
loitering time [sec] of the loitering people" in the case of a loitering map.
(Passing Map) 3-65535, and (Loitering Map) 1-655
Default setting: 50 (Passing map), 5 (Loitering map)

[Update] buttons
Update the heat map information displayed on the confirmation screen to the latest map information.

The heat map data is saved for each [Count data storage interval] based on the UTC time of 00:00:30 ± time zone after 5 minutes have passed since the [Heat Map Function] was changed to [On].

3.4.5Others

Count data storage interval
Sets the measurement interval of the count data. Creates a file for each measurement interval.
15 minutes, 1 hour, 12 hours, 24 hours
Default setting: 1 hour

Target to store of count data
Set the function to save the count data.

・

Cross Line Counting

・

Cross Line Counting + Heat Map

Default: Cross Line Counting

The storage period of the count data is as follows.

・When [Cross Line Counting] is selected: 732 days

・When [Cross Line Counting + Heat Map] is selected:

Cross Line Counting: 732 days

Heat map: 3 days (1 day if [Count data storage interval] is set to [15 min])

※In fact, the data will be stored for a longer period than the above storage period. The extra storage period depends on the camera time zone setting (up to 23 hours).
Example: Time zone +9.00

・When [Cross Line Counting] is selected: 732 days + 9 hours

・When [Cross Line Counting + Heat Map] is selected:

Cross Line Counting: 732 days + 9 hours

Heat map: 3 days + 9 hours (1 day + 9 hours when [Count data storage interval] is set to [15 min])

The interval for the transmission of ONVIF®
Set the ONVIF Metadata transmission interval.
(CROSS LINE count) 5 s, 10 s, 15 s, 1 min
(heat map) 1 min, 5 min, 15 min

Default setting:(CROSS LINE count) 5 s,
(heat map) 1 min

3.5Detailed setting (if necessary)

Set the detection sensitivity and duration of the AI-VMD and the size of the human to be detected.
Click [④ Detailed setting] at the top of the window to open the [Detailed setting] window.

[Set] button
Click to save the contents of the advanced tab currently displayed.

[Setting data initialization] button
Clicking this button initializes all AI-VMD settings.

3.5.1Image quality setting

[Batch change to the appropriate setting]
Click [Execute] to automatically set the appropriate image quality for AI-VMD in a batch. The items changed in the batch setting are the following.

Super Dynamic: Off
Light control speed : 8
White balance adjustment speed: 8
Digital noise reduction: 128
Intelligent Auto : Off
Automatic contrast adjust : Off

- If you select values larger than "Max. 1/30s" on [Image adjust] - [Light control mode] - [Maximum shutter], there may be loss of recognizability.
- If [Batch change to the appropriate setting] fails, update to the latest firmware and the latest version of WV-XAE200WUX before executing the process.

3.5.2AI-VMD alarm notification operation setting

Sets notification behavior for when alarm notification conditions are met.
An alarm is issued only when a motion is detected for the first time:
　Notification the first time the alarm conditions are met only.
An alarm is issued every time a motion is detected:
　Notification continuously as long as alarm conditions are met.
Default setting: An alarm is issued every time a motion is detected

3.5.3Threshold setting

Sets AI-VMD thresholds. This setting is common to all detection conditions.

[Human identification threshold]
Set the detection threshold for detecting as a human.
The smaller the value, the easier it is to detect as a human, but it is easier to detect incorrectly.
1~99

[Vehicle identification threshold]
Set the detection threshold for detecting as a vehicle.
The smaller the value, the easier it is to detect as a vehicle, but it is easier to detect incorrectly.
1~99

[Bicycle identification threshold]
Set the detection threshold for detecting as a bicycle.
The smaller the value, the easier it is to detect it as a bicycle, but it is easier to detect it incorrectly.
1~99

3.5.4Time setting

Sets the time from detection to alarm generation.

[Intruder detection time]
Sets the time from the detection of intrusion to the alarm generation.

0.2s, 0.4s, 1s, 2s, 3s, 4s, 5s, 10s

Default setting: 1s

[Loitering detection time]
Sets the time from the detection of stagnation until the alarm is generated.

10s, 20s, 30s, 1min, 2min, 5min, 10min, 15min, 20min, 30min, 40min, 50min, 60min

Default setting: 10s

Make sure that the detection frame continues to be displayed stably within the set time.

[Direction detection time]
Sets the time until the object continues to move in the specified direction and the alarm is generated.
1s, 2s, 3s, 4s, 5s, 10s
Default setting: 1s

Depending on the movement of the object, the time until the alarm is generated may be longer than the setting.

[Tailgating detection time]
This sets the time until tailgating detection is triggered. This setting is valid when cross line detection is set. An alarm is triggered when multiple objects are crossings line within a set time period. To detect with high accuracy, adjust the angle of view as follows.
1s, 2s, 3s, 4s, 5s, 6s, 7s, 8s, 9s, 10s
Default setting: Off

- Objects do not overlap each other.
- Objects are visible for more than 1 second before and after crossing the line.

3.5.5Speed setting

Set the alarm threshold for the speed to be detected. This is only valid for Detection area or detection lines where INTRUDER, DIRECTION or CROSS LINE is selected for Detection mode.

Click [Setup >>] to display the [Speed setting] screen.

・The camera used for this function must satisfy the following installation conditions.

・The camera is not tilted to the right or left.

・Flatten around the Detection area

・When this function is used, the Detection object must be displayed for 3 seconds or longer in the field of view.

The camera is not tilted to the right or left.

Flatten around the Detection area

・The speed detection accuracy depends on the viewing method of the subject and the environment. Be sure to check the operation at the installation site.

・This function is not compatible with the [Perpendicular angle mode]. To use this function, select [Normal angle mode] on the [Operation selection] screen.

On/Off the Speed setting
On or Off the Speed setting threshold.

On:Set the alarm threshold for the speed to be detected.

Off:No Speed setting is set.

Default setting: Off

[Use "inches", "feet", and "miles" as unit]
When checked, the km display changes to mile display, m display changes to ft display and cm display changes to inch display.
Default setting: Unchecked

3.5.5.1When [Speed setting] is [On]

For PTZ cameras, [Marker Setting] and [Detailed Setting] will not be displayed. [Camera Installation Info] will be displayed. For PTZ cameras, [Marker Setting] and [Detailed Setting] are not necessary. Instead, please configure [Camera Installation Info].

Basic settings

[Detection speed]
Set the detection speed as an alarm condition for the detected object. An alarm is triggered only when the moving speed of the detected object exceeds the detection speed.

(1) Check the detection object in the [Detection speed].

Human
Set alarm threshold for the speed of a human.

Vehicle
Set alarm threshold for the speed of a vehicle.

Bicycle
Set alarm threshold for the speed of a bircycle.

AI On-site Learning [X]: [Label1]
Set alarm threshold for the speed of new objects in AI On-site Learning [X].
This item is displayed only when registering new objects for AI On-site Learning. [X] will show a number from 1 to 5, and [Label1] will display the label name of the new object.

(2) Set the detection threshold in the range of 0-160.

(3) If you want to detect at a speed lower than a certain speed, check [Detect below specified speed] and enter the detection threshold value.

・The speed correspondence range depends on the viewing method of the subject and the environment. Estimated speeds are displayed on the demonstration screen.

[Camera height]
Set the height at which the camera is installed.
Default setting: 3.5 m

[Marker setting]
■ Setting procedure
Draw markers in at least two locations in the drawing area. Up to four markers can be drawn.
Next, enter a [Photographic subject size] for the drawn markers.
Clicking [Clear] clears the drawn markers.
When [Reflects markers in Depth Setting] is clicked, the markers set in the depth setting window are drawn.
[Marker setting] is not required for PTZ cameras.

Example of Marker Setting

For two markers

For four markers

To achieve higher-precision detection, please set the markers as follows:
- All markers should be set according to the actual height of the person.

- Place markers at a minimum of two locations within the white frame: one near and one far from the camera.
(Setting three or more markers may improve accuracy.)

- Enter the exact height of the person in [Photographic subject size].

Detailed setting

The value to be set here can be calculated automatically by the product. However, direct input may improve the calculation accuracy of the speed. If you want to enter the data directly, select [Use the value directly entered in ①] or [Use the value directly entered in ②] on the [Detailed setting].

[① Camera tilt corner]
Enter the tilt angle at which the camera is located.
Recommended range is 10°to 45°

[② Distance from directly under the camera to the center of the angle of view]
Enter the distance from the bottom where the camera is located to the center of the angle of view.
The center of the field angle is displayed as + in the live image.

Image of detailed setting

[Camera Installation Info]
For PTZ cameras, please configure [Camera Installation Info].

[Camaera Latitude]

Set the latitude of the camera's installation position.
-90.0000000 ~ 90.0000000
Default setting: 0

[Camera Longitude]

Set the longitude of the camera's installation position.
-180.0000000 ~ 180.0000000
Default setting: 0

[Latitude of center of angle of view]

Sets the latitude of the center of the angle of view. The “+” on the image screen is the center of the angle of view.
-90.0000000 ~ 90.0000000
Default setting: 0

[Longitude of center of angle of view]

Sets the longitude of the center of the angle of view. The “+” on the image screen is the center of the angle of view.
-180.0000000 ~ 180.0000000
Default setting: 0

・The latitude and longitude information of the camera installation location should be obtained from the map information such as the Google map.

・The latitude and longitude information for the center of the angle of view should be entered as the latitude and longitude of the ground level.

3.5.6Depth

Set the depth. The depth setting is common to both Detection program 1 and Detection program 2.
By setting the depth, objects detected as [humans] that are clearly not of the [humans] size are excluded from the target of alarm generation.

Click [Setup >>] to display [Depth setting] screen.

Depth setting method
Select the depth setting method.

On:Set the depth to the camera manually.

Off:The depth is not set.

Default setting: Off

・Use Normal angle mode.

・When it is often impossible to detect a human by setting it to [On], you may be able to detect it by selecting [Off].

[Use “inch” as unit]
When checked, the cm display changes to the inch display.
Default setting: Unchecked

3.5.6.1When [Depth setting] is [On]

■ Setting procedure
Draw marker 1 and marker 2 at two points in the drawing area.
Next, enter each [Photographic subject size] for Marker 1 and Marker 2.
Clicking [Clear] clears the drawn markers.

Example of Depth Setting

To achieve higher-precision detection, please set the markers as follows:
- All markers should be set according to the actual height of the person.
- Place markers at two locations within the white frame: one near and one far from the camera.
- Enter the exact height of the person in [Photographic subject size].

Size setting
When the depth setting is enabled, only the humans detected with sizes between the maximum and the minimum sizes trigger alarms.
Set the maximum size and the minimum size as the reference sizes (100%) for people 160 centimeters (63 inches) in height.

Max. size
Set the maximum size of the human to be detected.

100%, 150%, 200%, 250%, 300%, no limit

Default setting: 300%

Min. size
Set the minimum size of the human to be detected.

10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90%

Default setting: 50%

The following is an example of the setting.
e.g. Max. size: 150%, Min. size: 30%
An alarm is generated for a human between 48 cm (160×30%) and 240 cm (160×150%).

3.5.7Position selection (for PTZ cameras only)

For PTZ cameras, depth setting and Size setting are performed for each preset position.
Select the preset position to be set as follows.
Preset positions 1 to 16:Preset positions 1 to 16
Out of preset position:

Preset positions 17 to 256 and out-of-preset positions (common)

3.5.8Movement amount judgment

The alarm threshold for the movement to be detected can be set.

●

Off:This alarm sounds even if the movement of the object is very small.

●

Low:This alarm sounds even if the movement of the object is small.

●

Middle: Default setting

●

High:This alarm sounds when a large movement of an object is detected.

[Off] and [Low] may be useful for scenes where objects move forward from the rear when the camera is at a small angle. [High] may help reduce false alarms due to minor movements.

Movement amount judgment is valid only for Detection object who have selected INTRUDER for Detection mode.

3.5.9Advanced setting

Advanced setting the AI-VMD. Clicking + on the left side of the Advanced setting expands the items and displays the detailed settings.
Clicking the - mark on the left side of the Advanced setting will return to the previous window.

[Motion detection threshold]
Set the detection threshold for the movement of the object to be detected. This setting is reflected in the detection threshold for all objects.
The smaller the value, the easier it is to detect, but it is easier to detect incorrectly.
1~7

[AI-VMD information addition]
You can set whether to add AI-VMD data (detection frame, Detection object type) to video data or to display detection frame and Locus in live video of web browser.
When set to [On (with live display [with blue frame])], a blue frame is displayed when a movement is detected in the screen. When the detected motion enters the Detection area and an alarm is generated, the frame color turns red. The Locus of the detected moving object is indicated by a green line. Displays the Locus for the most recent 3 seconds.
From * V3.20, Locus is hidden.
The setting of adding AI-VMD data does not affect the alarm operation.

Off: AI-VMD does not add data. Also, the detection frame and Locus are not displayed.

On: Adds AI-VMD data, but does not display detection frame or Locus.

On(with live display):
Adds AI-VMD information and displays detection frame and Locus information. The blue frame is not displayed.

On(with live display [with blue frame]):
Adds AI-VMD data and displays detection frame and Locus. In addition to the red frame, the blue frame is also displayed.

Default setting: On (with live image display)

[Additional information type]
Sets the information to be added to the video data and the type of frame to be displayed in the live image of the web browser.
This setting is enabled when the above [AI-VMD Information addition] setting is set to [On (with live display)] or [On (with live display [blue frame]] or [On].
After * V3.20, the AI frame (green frame) will not be displayed.

With detection object information (alarm frame information):

Position information of detected object (human, vehicles, bicycles), the location of alarm frame (red frame), and motion detection frame (blue frame) is added.

With detection object information (AI frame information):

Adds information about the detected object (human, vehicles, bicycles) and the location of AI detected AI frames (green frame).

Without detected object information:

Only the positional information of the location of alarm frame (red frame) and the motion detection frame (blue frame) is added. The detected object information (human, vehicles, bicycles) is not added.

Default setting: With detection object information (alarm frame information)

[Detection Frame Notification]
Configure the notification conditions for detection frame positions in the ONVIF Analytics Stream. The display of detection frames on the demo screen will also be updated according to these settings.

Always notify:

Sends position information for alarm frames (red frame) and motion detection frames (blue frame) of detected objects.

Notify frames in detection area only:

Sends position information for alarm frames (red frame) and motion detection frames (blue frame) of objects detected within the designated detection area.

Notify frames immediately after alarm in detection area:

Sends position information for alarm frames (red frame) of objects detected within the detection area only at the time of initial detection.

Default setting: Always notify

[Simultaneous detection of detection objects]
When On, an alarm is notified when all of the selected detection objects are detected within the detection area for which Intruder, Loitering or Direction is selected as the detection mode.
Default setting: Off

[Alarm notification at the completion of detection]
Select whether to send an alarm when INTRUDER or LOITERING is finished.
Default setting: Off

When [Alarm notification at the completion of detection] is set to ON, the alarm may be notified regardless of the [Alarm deactivation time] of the camera.

[Target to which the upper limit of the detection size is applied]
Apply the upper limit to the selected Detection object size among humans, vehicles, or bicycles.
The selected Detection object excludes detection results with width or height of 1000 pixels or more.
Default setting: humans, vehicles, and bicycles are checked

[Settings related to ONVIF® Metadata]
Set the settings related to ONVIF Metadata.

Give the ClassCandidate to Analytics Stream

Select whether to attach a Class Candidate tag to the Analytics Stream.
Default setting: On

[Latitude / longitude sending settings]
Sets the latitude and longitude to be transmitted. Click [Setup >>] to display [Latitude / longitude sending settings] screen.

・The camera used for this function must satisfy the following installation conditions.

・The camera is not tilted to the right or left.

・Flatten around the Detection area

The camera is not tilted to the right or left.

Flatten around the Detection area

・The accuracy of detecting latitude and longitude depends on how the subject is viewed and the environment. Be sure to check the operation at the installation site.

・Use Normal angle mode.

Latitude / longitude sending settings

When [Latitude / longitude sendings] is set to [On], the software will send the object detection results as latitude and longitude position information in ONVIF. For cameras other than the PTZ camera, the following setting screen is displayed. For PTZ cameras, the [Marker setting] and [Detailed setting] menus are not displayed. [Marker setting] and [Detailed setting] are not required for PTZ cameras.

Basic settings

[Camera Installation Info]
Set the camera position. If [Azimuth] > [Automatic azimuth calculation] is checked, AI-VMD will calculate the azimuth angle from [Camera Latitude/Longitude] and [Latitude/Longitude of center of angle of view] on the map.

[Camaera Latitude]

Set the latitude of the camera's installation position.
-90.0000000 ~ 90.0000000
Default setting: 0

[Camera Longitude]

Set the longitude of the camera's installation position.
-180.0000000 ~ 180.0000000
Default setting: 0

[Latitude of center of angle of view]

Sets the latitude of the center of the angle of view. The “+” on the image screen is the center of the angle of view.
-90.0000000 ~ 90.0000000
Default setting: 0

[Longitude of center of angle of view]

Sets the longitude of the center of the angle of view. The “+” on the image screen is the center of the angle of view.
-180.0000000 ~ 180.0000000
Default setting: 0

[Azimuth]

[Automatic azimuth calculation] is checked.
The azimuth angle is calculated from the latitude and longitude of the camera and the latitude and longitude of the center of the angle of view.

[Automatic azimuth calculation] is unchecked.
Set the azimuth angle of the camera's installation position. Setting the latitude and longitude of the center of the field of view is not required.

0.0 ~ 359.9

Default setting: 0

・The latitude and longitude information of the camera installation location should be obtained from the map information such as the Google map.

・The latitude and longitude information for the center of the angle of view should be entered as the latitude and longitude of the ground level.

[Automatic azimuth calculation] is checked.

・For PTZ cameras, if the PAN operation is performed before clicking the [Set] button, the azimuth angle will not be automatically calculated after the PAN operation. If a PAN operation is performed between entering the latitude and longitude of the center of the angle of view and clicking the [Set] button, enter the latitude and longitude of the center of the angle of view again.

・For PTZ cameras, once the azimuth angle is set by clicking the [Setup] button, there is no need to re-set the azimuth angle after any PTZ operation; AI-VMD uses the camera's PTZ information to output latitude and longitude.

[Automatic azimuth calculation] is unchecked.

・The azimuth angle is the angle of the camera's center clockwise with the north at 0 degrees. Measure using a compass.

The following settings are the same as those of [Speed setting].

[Camera height]
Set the height at which the camera is installed.
Default setting: 3.5 m

[Marker setting]
■ Setting procedure
Draw markers in at least two locations in the drawing area. Up to four markers can be drawn.
Next, enter a [Photographic subject size] for the drawn markers.
Clicking [Clear] clears the drawn markers.
When [Reflects markers in Depth Setting] is clicked, the markers set in the depth setting window are drawn.
[Marker setting] is not required for PTZ cameras.

Example of Marker Setting

For two markers

For four markers

To achieve higher-precision detection, please set the markers as follows:
- All markers should be set according to the actual height of the person.

- Place markers at a minimum of two locations within the white frame: one near and one far from the camera.
(Setting three or more markers may improve accuracy.)

- Enter the exact height of the person in [Photographic subject size].

Detailed setting

The value to be set here can be calculated automatically by the product. However, direct input may improve the calculation accuracy of latitude and longitude. If you want to enter the data directly, select [Use the value directly entered in ①] or [Use the value directly entered in ②] on the [Detailed setting].

[① Camera tilt angle]
Enter the tilt angle at which the camera is located.
Recommended range is 10°to 45°

[② Distance from directly under the camera to the center of the angle of view]
Enter the distance from the bottom where the camera is located to the center of the angle of view.
The center of the field angle is displayed as + in the live image.

Image of detailed setting

・For PTZ cameras, [Detailed setting] is not required.

[Reference point for detecting objects]
You can select the reference point at which an object is judged to have entered the detection area or crossed the detection line. The reference point for detecting objects is displayed as a white dot on the configuration and demo screens of this extension software.
Default setting: Center of bottom edge

[Alarm Suppression Start Area]
When intrusion detection or line‑cross detection occurs in the Alarm Suppression Start Area or Alarm Suppression Start Line, alarm suppression is activated.During the configured alarm suppression duration, alarm notifications from other detection areas or detection lines will not be triggered, even if detection occurs.The Alarm Suppression Start Area/Line itself does not generate alarm notifications, even when detection occurs.
It functions solely as the trigger for starting alarm suppression.

On : Sets the alarm suppression start area. When set to On, the settings menu will be displayed.

Off: Cancels the alarm suppression start area.

Default setting:Off

Alarm Suppression Start Area Settings

Area to Use

Detection Area 1/Detection Area 2/Detection Area 3/Detection Area 4/Detection Area 5/Detection Area 6/Detection Area 7/Detection Area 8

Default setting:Detection Area 1

The alarm suppression start area can be set by selecting one from areas 1 to 8 in Detection Settings 1.
Only one area can be set as the alarm suppression start area.

Alarm Suppression Duration

1~600 (sec)

Default setting:300

Alarm suppression operation specifications

Conditions for starting alarm suppression

・

Alarm suppression starts when an intrusion or crossing line is detected in the alarm suppression start area/line.

Operation During Alarm suppression

・

During the alarm suppression duration, no alarm notification will be sent even if detection occurs in other areas or on other lines.

・

If a new detection occurs in the alarm suppression start area/line during the alarm suppression duration, the alarm notification suppression timer is reset and the suppression time count starts again.

Alarm suppression start area/line operation

・

The alarm suppression start area or line itself will not trigger an alarm even if an intrusion or line crossing is detected (it only functions as a trigger for starting suppression).

Alarm suppression start area (white frame in the figure below)

This is the detection area that triggers the start of alarm notification suppression (a state in which alarms are temporarily not issued).

Alarm suppression start line (white line in the diagram below)

The alarm suppression start line is the detection line that triggers the start of alarm notification suppression.

3.6Schedule setting

The initialization of AI-VMD schedules is always enabled by the Detection setting 1 and Detection setting 2.
To change the operation schedule, use the setting screen of the camera main unit to make the settings.
Refer to the camera operation manual for details.

3.7Alarm setting

Refer to the operation manual of the camera for the basic TCP alarm notification settings and other alarm settings.
Clicking [⑥ Alarm setting] at the top of the window opens the [Alarm Settings] window.

Alarm E-mail notification

[E-mail notification setup]
Click to display the mail setting screen of the camera.

Alarm image recording(SD memory card)

[SD memory card setup]
Click this button to display the SD Memory Card setting screen on the camera.

TCP alarm notification

[TCP alarm notification setup]
Clicking this button displays the TCP alarm notification settings window for the camera.

HTTP alarm notification

[HTTP alarm notification setup]
Clicking this button displays the HTTP alarm notification settings window for the camera.

MQTT alarm notification

[MQTT alarm notification setup]
Click this button to display the MQTT setting screen of the camera.

[Transmission]
When the check box is checked, the message is sent.
Default setting: Unchecked

[Topic]
Enter the name of the MQTT topic to be sent. Enter up to 128 half-pitch alphanumeric characters and symbols.

[QoS]
Select the level of QoS from 0, 1 and 2. 0<1<Communication quality is high with 2.

0:QoS0 delivers up to one message. Messages are not guaranteed to reach the server.

1:In QoS1, messages are delivered at least once. Messages are guaranteed to reach the Transmission destination, but may be duplicated.

2:QoS2 delivers the message exactly once. Messages are guaranteed to arrive only once without excess or deficiency.

Default setting: 1

[Retain]
Select to save the last message to the MQTT server.
Default setting: Off